HP OmniBook 3100 Скачать руководство пользователя

Страница: 36 / 107

HP OmniBook 2100/3000/3100

Removal and Replacement

2-13

3. Open the display fully.

4. Slide off the two plastic hinge covers about 5 mm, then lift them off. Use your finger or a small

tool to push outward next to the hinge.

5. Pry out and pop up the right end of the icon window cover at the plug-in module slot, then pop off

the cover.

Figure 2-9. Removing the Hinge Covers and Icon Window Cover

6. Pry off the two screw covers by the hinges (use a pointed knife or probe), then remove the two

screws.

For a 12-inch display, pry off the two display bumpers at the top of the display, then remove the
two additional screws.

Icon Window Cover

Hinge Cover (2)

Screw Cover (2)

Содержание OmniBook 3100












































































































Результаты поиска

Содержание OmniBook 3100

Отзывы:

Похожие инструкции для OmniBook 3100

Бренды по названию

Популярные бренды

HP OmniBook 3100, Руководство по обслуживанию

Результаты поиска

Содержание OmniBook 3100

Отзывы:

Похожие инструкции для OmniBook 3100

Бренды по названию

Популярные бренды