HP Engage One Retail System 143 Скачать руководство пользователя страница 59

Страница: 59 / 65

Configuring the software

Touch screen calibration for Windows 10 Professional and

Windows 10 IoT Enterprise for Retail

NOTE:

The Windows calibration tool works only in digitizer touch mode. If you install a retail touch utility, it

will set the touch screen to POS mode (mouse mode) by default and will not allow the Windows calibration

tool to run.

To calibrate the touch module in Windows 10 Professional and Windows 10 IoT Enterprise for Retail:

Open Control Panel. You can type

Control Panel

in the Search box to access it.

In Control Panel, type

calibrate

in the Search box. Under Tablet PC Settings, tap the Calibrate the

screen for pen or touch input link. In the Tablet PC Settings dialog box, tap the Calibrate button, and

then proceed to step 3.

Follow the on-screen instructions to press the target marks on the touch screen. At the end of the

calibration process, the touch module should be aligned with the video and the touch points will be

accurate.

Configuring optional HP integrated peripheral modules

To configure the integrated USB peripheral, refer to the HP Point of Sale Configuration Guide (available in

English only). The guide is located with the documentation on your retail computer and at

http://www.hp.com/support

. To access the guide on the retail computer, select Start, and then select

HP Point of Sale Information.

NOTE:

Check

http://www.hp.com/support

for updated software or documentation that became available

between the time your product was manufactured and the time it was delivered to you.

Touch screen calibration for Windows 10 Professional and Windows 10 IoT Enterprise for Retail

Содержание Engage One Retail System 143


































































Результаты поиска

Содержание Engage One Retail System 143

Отзывы:

Похожие инструкции для Engage One Retail System 143

Бренды по названию

Популярные бренды

HP Engage One Retail System 143, Справочник по аппаратуре

Результаты поиска

Содержание Engage One Retail System 143

Отзывы:

Похожие инструкции для Engage One Retail System 143

Бренды по названию

Популярные бренды