HP Engage One Retail System 143 Скачать руководство пользователя страница 54

Страница: 54 / 65

To test that the paper is loaded correctly, advance the paper with the paper feed button (1), and then

tear the excess paper off against the knife on the cover. A steady green LED (2) means the printer is on

and operating normally. If the LED is flashing, the cover may not be completely shut.

Thermal paper specifications

The printer requires qualified thermal paper with the following dimensions:

●

Width: 80 +0/-0.6 mm (3.15 +0/-0.03")

●

Diameter: 50.8 mm max. (2”)

The paper must not be attached at the roll’s core. Use paper with a colored stripe at the end to indicate that

the paper is running low.
The above figures are based on a core diameter of 22 ± 0.5 mm (0.87") outside and 11.5 ± 0.5 mm (0.45")

inside.

Qualified paper grades

Contact the manufacturer of your choice to order paper. HP recommends the following paper grades

produced by their respective manufacturers. There are a number of paper manufacturers qualified to provide

this paper, provided the POS paper rolls are from the recommended grades for monochrome (black ink)

paper.

Qualified manufacturers

Phone/Fax

Paper grade

Appvion, Inc. (USA)

825 E. Wisconsin Ave.

Appleton, WI 54912

http://www.appvion.com

Voice: (800) 922–1729

Fax: (800) 922–1712

Alpha 400-2.3 (was T1030)

Alpha 800-2.4 (was T1012A)

POS-Plus 600-2.4

Alpha 900-3.4 (was Superior)

All current Appvion papers are

BPA-free

Jujo Thermal Ltd.

P.O. Box 92 FI–27501

Voice: 358 (0) 10 303 200

Fax: 358 (0) 10 303 2419

AF50KS–E3

AP62KS–E3

Chapter 4 Using the column printer

Содержание Engage One Retail System 143


































































Результаты поиска

Содержание Engage One Retail System 143

Отзывы:

Похожие инструкции для Engage One Retail System 143

Бренды по названию

Популярные бренды

HP Engage One Retail System 143, Справочник по аппаратуре

Результаты поиска

Содержание Engage One Retail System 143

Отзывы:

Похожие инструкции для Engage One Retail System 143

Бренды по названию

Популярные бренды