manualshive.com logo in svg

HP E1563A, Руководство пользователя, Страница: 135 / 166

Поделиться
Скачать
HP E1563A Скачать руководство пользователя страница 135

HP E1563A and E1564A Register-Based Programming

135

Appendix B

Master-Slave

Operation

The HP E1563A and HP E1564A Digitizers can be configured in a  master-
slave configuration.  This configuration allows a master module and one or 
more slave modules to have their measurements synchronized.  
Synchronization occurs by having all channels trigger off of the same trigger 
event as well as all channels sampling from one sample signal.    

•

The sample synchronization signal is always generated by the master.

•

The TTL trigger event can be generated by either the master module or 

any of the slave modules.  This allows a slave module (as well as the 
master module) to use one of the four internal trigger sources or their 
external trigger source to trigger a measurement.    

Both the trigger signal and the sample signal are put on the VXI backplane 
TTL trigger (TTLT) lines where the master module and all slave modules 
receive the signals simultaneously.  TTL trigger lines are used in pairs 
between the master and slave(s) where one TTL trigger line carries the  
sample signal and the other carries the trigger signal.  The next section 
describes how these TTL trigger lines are paired.

Trigger Mode

Bits 5 and 6 of the Trigger Source/Control register are used to configure 
Digitizers for master-slave operation.  The module functions as a normal 
module when both bits are “0”.

NORMal Mode

The default setting for trigger mode is normal

 

(bits 5 and 6 of the Trigger 

Source/Control register are both “0”) which configures the module as an 
individual instrument.    

MASTer Mode

Bit 6 of the Trigger Source/Control register is used to configure a module as 
a master.  The eight TTL trigger lines (TTLT0-TTLT7) on the VXI 
backplane allow four different pairings as shown in Table 2-1 (MASTer0- 
SLAVe0, MASTer2-SLAVe2, MASTer4-SLAVe4 and  MASTer6- 
SLAVe6).  You must select an unused set of TTL trigger lines for the 
master-slave coupling when determining which master mode to set.  Do not 
use a TTLT line already used as a sample or trigger source.   

SLAVe Mode

Bit 5 of the Trigger Source/Control register is used to configure a module as 
a slave to a MASTer0 module.  MASTer0 and SLAVe0 modules share TTL 
trigger lines TTLT0 and TTLT1.  TTLT0 carries the sample signal and 
TTLT1 carries the trigger signal.  The following table shows all pairs of TTL 
trigger lines for each master-slave mode.    

Master-Slave Diagrams

Figure B-1 illustrates a module configured as a master module.  
Figure B-2 illustrates a module configured as a slave module.  

Table 3-2. Master-Slave Modes.

MASTer MODE

SLAVe MODE

Sample line

Trigger line

MASTer0

SLAVe0

TTLT0

TTLT1

MASTer2

SLAVe2

TTLT2

TTLT3

MASTer4

SLAVe4

TTLT4

TTLT5

MASTer6

SLAVe6

TTLT6

TTLT7

Содержание E1563A







































































































































































Отзывы:

Нет отзывов