HP 8920A Скачать руководство пользователя страница 248 | Manualshive

Страница: 248 / 658

background image

248

S:\HP892XX\USRGUIDE\manual\callscrn.fb

Chapter 6, Call Processing Subsystem

Using the ANALOG MEAS Screen

To Make an RF Sensitivity Measurement

1. If not already done, condition the Test Set.

See "Conditioning the Test Set for Call

Processing" on page 141

for further information.

2. If not already done, configure the Test Set.

See "Configure the Test Set" on page 142

for further information.

3. Connect the mobile station to the Test Set as shown in

Figure 17, "Connecting a

Mobile Station to the Test Set," on page 119

.

NOTE:

The mobile station’s speaker output must be connected to the Test Set’s AUDIO IN and the
mobile station’s microphone input must be connected to the Test Set’s AUDIO OUT in order
to use the ANALOG MEAS screen.

4. Turn on the mobile station.
5. Ensure that the Test Set is in the connected state.

See "Page a Mobile Station" on

for information on how to bring a mobile station up on a voice channel.

6. If the ANALOG MEAS screen is not displayed, select the

ANLG MEAS

field from the

To Screen

menu. The ANALOG MEAS screen will be displayed.

7. The following example illustrates how to make a 12 dB SINAD Receiver Sensitivity

measurement:
a. Select the

AFGen1 Freq

field and set it to 1 kHz.

b. Select the upper

AFGen1 To

field and set it to

FM

.

c. Select the lower

AFGen1 To

field and set it to 8 kHz.

d. Select the

AF Anl In

field and select

Audio In

.

e. Select the

Filter 1

field and select

C MESSAGE

.

f.

Select the

Filter 2

field and select

>99kHz LP

.

g. Position the cursor on the

De-Emphasis

field and select

Off

.

h. Select the

Detector

field and select

RMS

.

i.

Select the

AF Freq

measurement field and select

SINAD

.

j.

Select the

Amplitude

field and begin to lower the transmitted base station voice

channel power until 12 dB SINAD is reached.

k. The mobile station might mute or drop off the air before a 12 dB SINAD is reached.

The performance of the mobile station at low RF levels is dependent upon the char-
acteristics of the mobile station (that is, what type of system it is designed for). Un-
like a real base station, the Test Set does not perform any protocol functions on the
voice channel.

«
...
246
247
248
249
250
...
»

Содержание 8920A



















































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 8920A

Бренд: Taurus Страницы: 28

Бренд: Kärcher Страницы: 54

Бренд: ABB Страницы: 85

Бренд: Napoleon Страницы: 2

Бренд: Raytheon Страницы: 62

Бренд: Tascam Страницы: 8

Бренд: B-K lighting Страницы: 5

Бренд: B-K lighting Страницы: 4

Бренд: B-K lighting Страницы: 3

Бренд: LAWO Страницы: 459

Бренд: earline Страницы: 13

Бренд: Cameo Страницы: 64

Бренд: Cameo Страницы: 100

Бренд: CAME Страницы: 32

Бренд: Harken Страницы: 4

Бренд: Harken Страницы: 2

TERRA FORCE BOOM

Бренд: Hardi Страницы: 40

Бренд: Harken Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды