HP 8920A Скачать руководство пользователя страница 114 | Manualshive

Страница: 114 / 658

background image

114

S:\HP892XX\USRGUIDE\manual\callscrn.fb

Chapter 6, Call Processing Subsystem

Description of the Call Processing Subsystem

Description of the Call Processing Subsystem

The Call Processing Subsystem, which comprises six call processing screens,
allows the Test Set to simulate a cellular base station. The Call Processing
Subsystem provides, through host firmware control, the specific signals and
protocol messages necessary to automatically establish and maintain a cellular
link between the Test Set and a cellular phone (mobile station).

Once the link is established the operator can exercise the call processing functions
of the mobile station, such as

•

the decoding of orders from the base station, such as orders to retune the transceiver to
a new channel, to alert the mobile station user to an incoming call, to adjust the
transceiver output power level, or to release the mobile station upon completion of a
call.

the encoding of signaling information for transmission to the base station, such as dialed
digits for call origination, disconnect signal at the completion of a call, or mobile identifi-
cation number.

the authentication signaling associated with AMPS (IS-54) call processing such as shared
secret data update, unique challenge, origination with authentication, and page with
authentication.

In addition, when the link is established the Test Set performs the following
functions automatically:

•

measures some of the basic RF characteristics of the mobile station’s transmitted
carrier, such as; transmitter power, frequency accuracy, and modulation deviation

•

decodes and displays various reverse control channel and reverse voice channel
signaling messages

When sending forward control channel and forward voice channel messages, you
can set the bit pattern to an industry standard or to a pattern of your choice. The
ability to set the bit patterns gives the operator the opportunity to interject errors
into the signaling message, and test the mobile station’s ability to find these
errors.

«
...
112
113
114
115
116
...
»

Содержание 8920A



















































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 8920A

Бренд: Facsimile Страницы: 16

Бренд: Mainca Страницы: 21

Бренд: Daktronics Страницы: 30

Бренд: DAKOTA ULTRASONICS Страницы: 28

Бренд: Gebhardt Anlagentechnik Страницы: 152

Бренд: Hach Страницы: 58

Бренд: Hach Страницы: 52

AquaPure Ei Series

Бренд: Jandy Страницы: 4

AquaPure Ei Series

Бренд: Jandy Страницы: 8

Jandy Pro Series

Бренд: Jandy Страницы: 16

Бренд: Kellfri Страницы: 12

Бренд: Vapotherm Страницы: 32

Бренд: Vanguard Instruments Страницы: 47

MCX-C15 - MusicCAST Network Audio Player

Бренд: Yamaha Страницы: 65

Бренд: Yamaha Страницы: 24

Бренд: Jackson Страницы: 2

Бренд: Vag Страницы: 10

Cell Saver Elite+

Бренд: Haemonetics Страницы: 230

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды