HP 8920A Скачать руководство пользователя страница 406 | Manualshive

Страница: 406 / 658

background image

406

S:\HP892XX\USRGUIDE\manual\encoscrn.fb

Chapter 10, Signaling Encoder (AF Generator 2)

MPT 1327 Encoder

Control Channel

The

Control Channel

field allows you to enter the Control Channel number.

Radio units (RU) are programmed to look for control channel signaling on a
restricted set of radio channels, known as the hunt group. It is essential that the
channel number on which the Test Set transmits the control channel signaling
matches one of the channels in the RU’s hunt group. If there is not a match, no
communication will be possible.

The control channel is a four-digit decimal integer without leading zeros. It has
the range 0 through 1023, and its default value is 1.

Test Mode

The

Test Mode

field is used to select how the encoder is used for tests:

Selection

Description

Off

In this mode the signaling hardware is disabled and does not transmit
data.

Control

In this mode the signaling hardware is enabled and is retransmitting a
basic control channel structure as defined by the content of the filler
buffer. (Refer to

"Forward Control Channel Message and Filler

Buffers" on page 408

for an explanation of the filler buffer). One or

more timeslots in the filler pattern can be overlaid by messages from
the control message buffer under control of the

Send

field.

Traffic

In this mode the signaling hardware is enabled. The filler pattern is
not transmitted. Single or multi-timeslot messages can be transmitted
from the traffic message buffer under the control of the

Send

field.

1200Hz

In this mode the signaling hardware is enabled and transmits a contin-
uous 1200 Hz tone (equivalent to an FFSK transmission of continu-
ous ones).

1800Hz

In this mode the signaling hardware is enabled and transmits a contin-
uous 1800 Hz tone (equivalent to an FFSK transmission of continu-
ous zeros).

Dotting

In this mode the signaling hardware is enabled and transmits alternat-
ing 1200 Hz and 1800 Hz tones (equivalent to an FFSK transmission
of alternating ones and zeros).

«
...
404
405
406
407
408
...
»

Содержание 8920A



















































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 8920A

Бренд: Fein Страницы: 248

Бренд: ZF Страницы: 30

Бренд: Raymarine Страницы: 111

Бренд: Palazzetti Страницы: 112

Бренд: Makita Страницы: 17

Бренд: Makita Страницы: 13

Бренд: NEC Страницы: 54

WJHD309A - DIGITAL DISK RECORDER

Бренд: Panasonic Страницы: 79

Бренд: National Instruments Страницы: 10

Бренд: Nederman Страницы: 89

Бренд: Nederman Страницы: 71

Бренд: Nederman Страницы: 131

Бренд: X-Cite Страницы: 2

Бренд: Abus Страницы: 12

Бренд: ALL-FILL Страницы: 32

ESK+ Manual Knee Lock

Бренд: Blatchford Страницы: 172

Бренд: HEINE OPTOTECHNIK Страницы: 52

Бренд: Ugin Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды