HP 8920A Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 658

background image

5

Safety Considerations for this Instrument

WARNING

This product is a Safety Class I instrument (provided with a protective
earthing ground incorporated in the power cord). The mains plug shall only
be inserted in a socket outlet provided with a protective earth contact. Any
interruption of the protective conductor inside or outside of the product is
likely to make the product dangerous. Intentional interruption is
prohibited.

Whenever it is likely that the protection has been impaired, the instrument
must be made inoperative and be secured against any unintended operation.

If this instrument is to be energized via an autotransformer (for voltage
reduction), make sure the common terminal is connected to the earth
terminal of the power source.

If this product is not used as specified, the protection provided by the
equipment could be impaired. This product must be used in a normal
condition (in which all means for protection are intact) only.

No operator serviceable parts in this product. Refer servicing to qualified
personnel. To prevent electrical shock, do not remove covers.

Servicing instructions are for use by qualified personnel only. To avoid
electrical shock, do not perform any servicing unless you are qualified to do
so.

The opening of covers or removal of parts is likely to expose dangerous
voltages. Disconnect the product from all voltage sources while it is being
opened.

Adjustments described in the manual are performed with power supplied to
the instrument while protective covers are removed. Energy available at
many points may, if contacted, result in personal injury.

The power cord is connected to internal capacitors that my remain live for
5 seconds after disconnecting the plug from its power supply.

For Continued protection against fire hazard, replace the line fuse(s) only
with 250 V fuse(s) or the same current rating and type (for example, normal
blow or time delay). Do not use repaired fuses or short circuited
fuseholders.

«
...
3
4
5
6
7
...
»

Содержание 8920A



















































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 8920A

Бренд: Tacx Страницы: 2

Бренд: C.E. Nierhoff & Co Страницы: 7

Бренд: Haigh Страницы: 60

Бренд: Olsen Страницы: 4

Dominator Series

Бренд: Falcon Страницы: 31

Бренд: Fakir Страницы: 22

Growers Supply 109722

Бренд: FarmTek Страницы: 9

Бренд: ParaBody Страницы: 5

Бренд: tayco Страницы: 111

Бренд: Rainin Instrument Страницы: 16

Бренд: Xtool Страницы: 8

ZA top SM315.100A

Бренд: ZIEHL-ABEGG Страницы: 76

SHAKER KEEPER 20V 200

Бренд: Garland Страницы: 84

Бренд: Kellfri Страницы: 44

Retractable Box Scrapers HR3584

Бренд: Land Pride Страницы: 1

Бренд: Lutron Electronics Страницы: 10

Бренд: Mikrona Страницы: 12

Бренд: Mark Fitness Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды