HP 8920A Скачать руководство пользователя страница 186 | Manualshive

Страница: 186 / 658

background image

186

S:\HP892XX\USRGUIDE\manual\callscrn.fb

Chapter 6, Call Processing Subsystem

Using the CALL DATA Screen

Using the CALL DATA Screen

To View the Decoded Reverse Channel Words from a Mobile Station Registration

1. If not already done, condition the Test Set.

See "Conditioning the Test Set for Call

Processing" on page 141

for further information.

2. If not already done, ensure that the Test Set is properly configured.

See "Configure the

Test Set" on page 142

for further information.

3. Connect the mobile station to the Test Set as shown in

Figure 17, "Connecting a

Mobile Station to the Test Set," on page 119

.

4. Turn on the mobile station.
5. If the CALL DATA screen is not displayed, select

CALL DATA

from the

To Screen

menu. The CALL DATA screen will be displayed.

6. Select the

Active

field. The

Active

annunciator will light when the control channel

is turned on.

7. Select the

Register

field. The

Register

annunciator will light while the

registration is in process. If the mobile station responds properly on the reverse control
channel, the message

RECC Return

will flash momentarily in the upper right-hand

corner of the CALL CONTROL screen. The

Active

annunciator will light when the

registration has successfully completed.

8. Select the

Display Word

field. A list of reverse channel words which can be

displayed will appear in a

Choices:

menu. Select the desired word from the list of

choices. The decoded contents for each of the fields in the selected word will be
displayed in the lower portion of the display.

9. If a word is chosen which was not part of the decoded reverse channel message stream,

all the fields will be blank when it is displayed.

10.

See "CALL DATA Screen Message Field Descriptions" on page 170

for a

description of each of the available reverse channel words.

Step 7. and Step 8. in the above procedure can be reversed, that is, the desired
word can be selected first, then the mobile station can be registered. If the
registration is successful, the contents of each display word contained in the
reverse control channel’s message stream will be updated when the decoding is
complete.

The registration does not have to happen while you are viewing the CALL DATA screen.
When the CALL DATA screen is viewed, the contents of the display words will be the
decoded data from the last successful call processing function (registration, origination,
page, release, order).

«
...
184
185
186
187
188
...
»

Содержание 8920A



















































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 8920A

Бренд: MAHLE Страницы: 21

Бренд: YATEK Страницы: 72

Бренд: Backyard Discovery Страницы: 51

Бренд: Nautilus Страницы: 12

Бренд: CAIRE Страницы: 16

Sportsound SSR-200

Бренд: Daktronics Страницы: 5

Бренд: Haki Страницы: 24

Бренд: Dakota Digital Страницы: 5

Бренд: YASKAWA Страницы: 40

RAISED GARDEN BED

Бренд: Yardfully Страницы: 2

Z9 Commercial Collection System Z9A

Бренд: Yazoo/Kees Страницы: 3

Z9 Commercial Collection System Z9A

Бренд: Yazoo/Kees Страницы: 36

Бренд: YASKAWA Страницы: 1166

Quadro A Legs 3P 120 Degree Workstation with...

Бренд: Jason.L Страницы: 10

Бренд: SAC Страницы: 2

Бренд: Airway Страницы: 2

Бренд: Crazy Foil Страницы: 8

Бренд: Delfield Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды