HP 8920A Скачать руководство пользователя страница 142 | Manualshive

Страница: 142 / 658

background image

142

S:\HP892XX\USRGUIDE\manual\callscrn.fb

Chapter 6, Call Processing Subsystem

Using the CALL CONTROL Screen to Test Call Processing Functions

2. Couple the variable-frequency notch filter to AFGen1.

This step is only required if audio testing is to be done on the mobile station. This step
couples the variable-frequency notch filter to the output frequency of AFGen1 (audio
frequency generator1). The notch filter is used when making SINAD measurements.
AFGen1 is used to generate the audio tone for the SINAD measurement. Coupling the
notch filter to the audio source ensures the most accurate measurement.

a. Press and release the blue SHIFT key and then the DUPLEX key to display the

CONFIGURE screen.

b. Position the cursor on the

Notch Coupl

field and select

AFGen1

.

Configure the Test Set

Select

CALL CNTL

from the

To Screen

menu. The CALL CONTROL screen will be

displayed.

3. Verify that the Test Set configuration information is appropriate for the mobile station

to be tested. Check the following fields:
a.

System Type

- Select the type of cellular system to be simulated (AMPS,

NAMPS, TACS, JTACS, DAMPS, DCCH).

If the

System Type

field was modified in step3. a. the control channel will become

active since modifying this field automatically activates the control channel. Refer to the

System Type

field description, on page 136

b.

Cntl Channel

- Set the control channel number to be used by the Test Set.

NOTE:

If the

Cntl Channel

field was modified in step 3.b. the control channel will become active

since modifying this field automatically activates the control channel. Refer to the

field description, on page 126

c.

Amplitude

- Set the output power of the Test Set’s transmitter (that is, the output

power of the Test Set’s RF Generator).

d.

SID

- Enter the system identification number of the Test Set as a decimal number.

e.

Chan:

(right-hand field) - Enter the voice channel number which will be assigned

to the mobile station by the Test Set as either an initial voice channel assignment or
as a handoff voice channel assignment.

f.

Ch Loc:

(right-hand field,

NAMPS

system type only) - Select the narrow analog

channel location which will be assigned to the mobile station by the Test Set as ei-
ther an initial channel location assignment or as a handoff channel location assign-
ment. The choices are Lower (10 kHz below standard wide analog channels),
Middle (centered at the wide analog channel), Upper (10 kHz above the standard
analog channel) or Wide Chan.

«
...
140
141
142
143
144
...
»

Содержание 8920A



















































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 8920A

Бренд: Walker Bay Страницы: 8

Бренд: Makita Страницы: 10

Бренд: Olsen Страницы: 56

Бренд: Waterous Страницы: 5

Бренд: 3TECH Страницы: 32

Бренд: 4EVAC Страницы: 15

Бренд: YATEK Страницы: 72

Бренд: ACE INSTRUMENTS Страницы: 15

Бренд: Wave Fitness Страницы: 15

Бренд: Quadro Страницы: 11

Бренд: G-Systems Страницы: 60

Бренд: G-Lab Страницы: 16

Бренд: G&G Страницы: 2

Бренд: Idmed Страницы: 2

Бренд: Keller Страницы: 12

Бренд: MacDon Страницы: 49

Бренд: MacDon Страницы: 49

Бренд: MacDon Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды