HP 8920A Скачать руководство пользователя страница 196

Страница: 196 / 658

196

S:\HP892XX\USRGUIDE\manual\callscrn.fb

Chapter 6, Call Processing Subsystem

CALL BIT Screen

Message Contents that can be Modified Using the CALL BIT screen

The contents of twenty nine different messages can be modified from this screen.
The message to be modified is selected using the

Set Message

field. The eleven

messages whose contents can be modified are:

•

Forward Control Channel Messages for Paging, Origination, Order Confirmation, and
Orders.

•

SPC WORD1

- System Parameter Overhead Message Word 1

•

SPC WORD2

- System Parameter Overhead Message Word 2

•

ACCESS

- Access Type Parameters Global Action Message

•

REG INC

- Registration Increment Global Action Message

•

REG ID

- Registration ID Message

•

C-FILMESS

- Control-Filler Message

•

MS WORD1

- FCC mobile station control message Word 1- Abbreviated Address

Word

•

MS IntVCh

- FCC mobile station control message Word 2- Extended Address-

Word - Voice Channel Assignment

•

MSMessOrd

- FCC mobile station control message Word 2- Extended Address

Word - Order

•

FVC V Mes

- FVC Mobile Station Control Voice Channel Assignment Message

FVC O Mes

- FVC Mobile Station Control Order Message

•

Forward Control Channel Authentication Messages.

•

RandChalA

- Random Challenge A Global Action Message

•

RandChalB

- Random Challenge B Global Action Message

•

RAND SSD1

- First SSD Update Order Word

•

RAND SSD2

- Second SSD Update Order Word

•

RAND SSD3

- Third SSD Update Order Word

•

BSChalCon

- Base Station Challenge Order Confirmation Word

•

UniqChOrd

- Unique Challenge Order Word

•

Forward Voice Channel Authentication Messages.

•

FVC SSD1

- First SSD Update Order Word

•

FVC SSD2

- Second SSD Update Order Word

•

FVC SSD3

- Third SSD Update Order Word

•

FVCBSCon

- Base Station Challenge Order Confirmation

•

FVCUniqCh

- Unique Challenge Order Word

Содержание 8920A



















































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 8920A

Отзывы:

Похожие инструкции для 8920A

Бренды по названию

Популярные бренды

HP 8920A, Руководство пользователя

Результаты поиска

Содержание 8920A

Отзывы:

Похожие инструкции для 8920A

Бренды по названию

Популярные бренды