HP 8920A Скачать руководство пользователя страница 249 | Manualshive

Страница: 249 / 658

background image

249

Chapter 6, Call Processing Subsystem

Using the ANALOG MEAS Screen

To Make an FM Hum and Noise Measurement

1. If not already done, condition the Test Set.

See "Conditioning the Test Set for Call

Processing" on page 141

for further information.

2. If not already done, configure the Test Set.

See "Configure the Test Set" on page 142

for further information.

3. Connect the mobile station to the Test Set as shown in

Figure 17, "Connecting a

Mobile Station to the Test Set," on page 119

.

NOTE:

The mobile station’s speaker output must be connected to the Test Set’s AUDIO IN and the
mobile station’s microphone input must be connected to the Test Set’s AUDIO OUT in order
to use the ANALOG MEAS screen.

4. Turn on the mobile station.

Ensure that the Test Set is in the connected state.

See "Page a Mobile Station" on page

for information on how to bring a mobile station up on a voice channel.

5. If the ANALOG MEAS screen is not displayed, select the

ANLG MEAS

field from the

To Screen

menu. The ANALOG MEAS screen will be displayed.

NOTE:

It is recommended that the mobile station’s microphone be muted, if possible, when making
measurements on the mobile stations RF carrier. If the microphone is not muted it is possible
for extraneous noise to be picked up by the microphone and adversely affect the
measurements.

6. The following example illustrates how to make a FM Hum and Noise measurement:

a. Select the

Amplitude

field and set it to

−

47 dBm.

b. Select the

AFGen1 Freq

field and set it to 1 kHz.

c. Select the upper

AFGen1 To

field and set it to

Audio Out

.

d. Select the

AF Anl In

field and select

FM Demod

.

e. Select the

Filter 1

field and select

C MESSAGE

.

f.

Select the

Filter 2

field and select

>99kHz LP

.

g. Position the cursor on the

De-Emphasis

field and select

750 us

.

h. Select the

Detector

field and select

PK+

.

i.

Select the measurement field and select

AF Freq

.

j.

Select the lower

AFGen1 To

field and adjust the signal level until the

FM Devi-

ation

field on the upper portion of the CRT reads 8 kHz.

k. Select the

Detector

field and select

RMS

.

l.

Select the

FM Deviation

field.

m. Press the blue SHIFT key, the INCR -10 key, then the ENTER key. This sets a zero

reference point.

n. Select the lower

AFGen1 To

field and press the ON/OFF key. This turns off the

modulating signal to the mobile station transmitter.

o. The FM Hum and Noise figure is displayed in the

FM Deviation

field.

«
...
247
248
249
250
251
...
»

Содержание 8920A



















































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 8920A

D-MAS HyperSat 2540

Бренд: DanMedical Страницы: 103

Бренд: CAB Страницы: 13

Бренд: CAB Страницы: 30

Бренд: CAB Страницы: 17

Бренд: CAB Страницы: 33

Camping Equipment

Бренд: C. Crane Страницы: 8

Бренд: C-Pro Direct Страницы: 4

Бренд: C-Pro Direct Страницы: 4

Бренд: Panlux Страницы: 2

DISHSTAR ADA-SEER

Бренд: Jackson Страницы: 2

Varycolor MICRO 150HTI

Бренд: JB-Lighting Страницы: 18

Бренд: NanoVibronix Страницы: 2

Бренд: NanoVibronix Страницы: 32

Shapes Hexagons

Бренд: Nanoleaf Страницы: 27

Бренд: Zero88 Страницы: 26

Бренд: HAMOKI Страницы: 7

Бренд: H&S Страницы: 56

Бренд: RAMVAC Страницы: 53

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды