HP 16533A Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 152

HP 16533A Скачать руководство пользователя страница 91

Grid Field

The oscilloscope display can optionally be divided into horizontal and
vertical grids by using the Grid On or Grid Off feature of the display.
Touching the Grid field will toggle the field between On and Off. The default
setting for the Grid field is Off.

On

Touching the Grid field when it reads Off will toggle the field to On, and will
cause the screen to display a horizontal and vertical grid pattern.

In either Normal or Average modes, the grid can be turned On when the
oscilloscope is not currently running and the grid will appear on screen
immediately. If the oscilloscope is currently acquiring data, the grid will be
drawn when the acquisition is completed. In Accumulate mode, the grid can
be turned on at any time, but it will not be drawn until the next acquisition is
completed or some change is made to the display screen that would cause
the display to be erased and redrawn (that is: s/div, etc).

Off

Touching the Grid field when it reads On will toggle the field to Off, and will
remove the grid pattern from the screen.

In either Normal or Average modes, the grid can be turned Off when the
oscilloscope is not currently running and the grid will be erased from the
screen immediately. If the scope is currently acquiring data, the grid will be
erased when the current acquisition is completed. In Accumulate mode, the
grid can be turned off at any time, but it will not be erased from the screen
until some change is made to the display screen that would cause the display
to be erased and redrawn (that is: s/div, etc).

The Display Menu

Grid Field

7-7

«
...
89
90
91
92
93
...
»

Содержание 16533A

























































































































































Отзывы:

Нет отзывов