HP 16533A Скачать руководство пользователя страница 136 | Manualshive

Страница: 136 / 152

HP 16533A Скачать руководство пользователя страница 136

Self Cal menu calibrations

1

Load the default calibrations factors.

Note that once the default calibration factors are loaded, all calibrations
must be done. The calibration must be performed in the exact sequence
listed below.

N O T E

The calibration PROTECT/UNPROTECT switch on the HP 16533/34A
Oscilloscope module must be set to UNPROTECT.

a

Touch the Module field, then at the pop-up menu touch the Scope
card to be calibrated.

b

Touch the Menu field, then at the pop-up menu touch Calibration.

c

Touch the Mode field, then at the pop-up menu touch Service Cal.

d

Touch the Procedure field, then at the pop-up menu touch Default
Values.

e

Touch the Start field, then follow the instructions on the display.

Messages will be displayed as each operational accuracy calibration routine
is completed to indicate calibration has passed or failed. The resulting
calibration factors are automatically stored to nonvolatile RAM at the
conclusion of each calibration routine.

Installation and Operator’s Service

Self Cal menu calibrations

11–12

«
...
134
135
136
137
138
...
»

Содержание 16533A

























































































































































Отзывы:

Нет отзывов