HP 16533A Скачать руководство пользователя страница 127 | Manualshive

Страница: 127 / 152

HP 16533A Скачать руководство пользователя страница 127

To inspect the module

1

Inspect the shipping container for damage.

If the shipping container or cushioning material is damaged, keep them until
you have checked the contents of the shipment and checked the instrument
mechanically and electrically.

2

Check the supplied accessories.

3

Inspect the product for physical damage.

Check the module and the supplied accessories for obvious physical or
mechanical defects. If you find any defects, contact your nearest
Hewlett-Packard Sales Office. Arrangements for repair or replacement are
made, at Hewlett-Packard’s option, without waiting for a claim settlement.

To prepare the mainframe

C A U T I O N

Turn off the mainframe power before removing, replacing, or installing the
module.

C A U T I O N

Electrostatic discharge can damage electronic components. Use grounded
wrist straps and mats when performing any service to this module.

1

Turn off the mainframe power switch, then unplug the power cord.
Disconnect any input or output connections.

2

Plan your module configuration.

If you are installing a one-card module, use any available slot in the
mainframe, unless you also have an HP 16530/31 module in the mainframe.
If there is an HP 16530/31 module in the mainframe, the HP 16534 module
must be seated above the HP 16530/31 module.

If you are installing a multi-card module, use adjacent slots in the
mainframe. See illustration on next page for multi-card combinations.

Installation and Operator’s Service

To inspect the module

11–3

«
...
125
126
127
128
129
...
»

Содержание 16533A

























































































































































Отзывы:

Нет отзывов