HP 16533A Скачать руководство пользователя страница 110 | Manualshive

Страница: 110 / 152

HP 16533A Скачать руководство пользователя страница 110

Example

To overlay the waveform on Input 1 with the waveform on Input 2:

Touch the Channel Mode field on the display, then when the pop-up appears,
touch the Overlay field.

Turn the knob so that the bottom input in the channel label field is
highlighted in white.

Then touch the Action field until Insert is displayed.

Next, touch the Input 1 label in the Labels field, then touch Input 2 in the
Labels field.

Input 1 and Input 2 waveforms, shown as X1,X2 (where X is the slot letter of
the module) are then displayed in the top channel label field.

After you have touched the Done key in the pop-up, you may need to touch
the s/Div field and change the sweep speed in order to more easily see
differences in the overlaid waveforms.

Input 1 will now be overlaid on Input 2 in the waveform display area.

No voltage values for the overlaid waveforms will appear in the channel
label field to the left of the waveform display area.

Overlaid waveforms are scaled and offset (respectively), or in relationship to
each other, but the value in the V/Div field does not necessarily correlate to
the overlay waveform display tick marks.

The Waveform Selection Menu

Channel Mode Field

9-6

«
...
108
109
110
111
112
...
»

Содержание 16533A

























































































































































Отзывы:

Нет отзывов