HP 16533A Скачать руководство пользователя страница 122

Страница: 122 / 152

Supplemental Characteristics

Digitizer

A/D Resolution:

8 bits (1 part in 256) real time, 4 vertical divisions

(+/- 0.4%).

Digitizing Rate

Up to 1 Gigasample per second (HP 16533A).
Up to 2 Gigasample per second (HP 16534A).

Digitizing Technique:

Real-time digitizing; each 32,768 samples are

acquired on a single acquisition.

Acquisition Memory Size:

32,768 samples per channel.

Waveform Record Length:

32,768 points.

Waveform Display

Displayed Waveforms

Eight waveform windows maximum, with

scrolling across 96 waveforms.

Display Formats

Waveforms can be displayed in an overlapping

and/or non-overlapping format. Display capability of A-B and A+B is
also provided.

Display Resolution

500 points horizontal, 240 points vertical.

Display Modes

Normal (Single)

New acquisition replaces old acquisition on screen.

Accumulate

New acquisition is displayed in addition to previous

acquisitions until screen is erased.

Average

New acquisitions are averaged with old acquisitions, with the

updated waveform displayed until erased. Maximum number of
averages is 256.

Overlay

Up to 8 acquired waveforms from separate channels can be

overlayed in the same display area.

Specifications and Characteristics

Supplemental Characteristics

10–6

Содержание 16533A

























































































































































Результаты поиска

Содержание 16533A

Отзывы:

HP 16533A, Справочник пользователя, Страница: 122 / 152

Результаты поиска

Содержание 16533A

Отзывы: