HP 16533A Скачать руководство пользователя страница 120

Страница: 120 / 152

Characteristics

The characteristics are not specifications, but are included as additional
information.

VERTICAL (at BNC Input):

Vertical Sensitivity:

4 mV/div to 10 V/div Range (1:1 Probe) in 1:2:4

increments

DC Offset Range (1:1 Probe):

Vertical Sensitivity

Available Offset

4mV - 100mV/div

+/- 2V

100mV - 400mV/div

+/- 10V

400mV - 2.5V/div+/- 50V
2.5V - 10V/div

+/- 250V

Probe Factors:

Any integer ratio from 1:1 to 1000:1

Maximum Safe Input Voltage:

1 M

Ω

+/-250V (dc+ac, 10KHz), CAT I

Ω

5 V rms, CAT I

Channel-to-Channel Isolation: (With Channels at equal sensitivity)

dc to 50 MHz:

40 dB

50 MHz to 250 MHz (HP 16533A):30 dB
50 MHz to 500 MHz (HP 16534A):30 dB

Number of Channels:

2,4,6,8 simultaneous channels using the same

trigger OR up to 10 with independent triggers for each pair of channels.
Maximum of 20 channels with HP 16501A expansion frame.

Rise Time*:

1.4 ns (HP 16533A) and 700 ps (HP 16534A)

Vertical (dc) Gain Accuracy**:

+/-1.25% of full scale

Input Coupling:

1 M

Ω

ac, dc

Ω

dc only

Input C:

Approximately 7 pF

Probes Included:

Two HP 10441A probes:10:1, 10 M

Ω

, 9 pF, 2 meter

* Rise time is calculated from

0.35

bandwidth

** Vertical gain accuracy decreases 0.08% per

C from software calibration temperature

Specifications and Characteristics

Characteristics

10–4

Содержание 16533A

























































































































































Результаты поиска

Содержание 16533A

Отзывы:

HP 16533A, Справочник пользователя, Страница: 120 / 152

Результаты поиска

Содержание 16533A

Отзывы: