HP 16533A Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 152

HP 16533A Скачать руководство пользователя страница 53

Done Field

You touch the Done field when you are done entering data in the
auto-markers pop-up and want to return to the waveform display.

Set on Field

The Set on field assigns an input waveform to the Tx or To marker, or allows
the marker to be set manually (with the MANUAL selection in the pop-up).
When you touch the Set on field, a pop-up appears showing all waveform
sources available.

What is displayed on the pop-up depends on how many oscilloscope boards
are installed in the mainframe and in which slots they are installed.

The default selection for the Set on field is the lowest letter and number
combination. For example, if oscilloscope boards are installed in mainframe
slots C and D, the Set on field will default to C1 for both the Tx and To
markers.

Type Field

The Type field selects the units in which an automatic time marker level will
be specified. The automatic time marker can have a level expressed as either
a percentage of the waveform top-base voltage (Percent) or as an absolute
voltage level (Absolute).

The default selection is Percent.

The Marker Menu

Done Field

5-11

«
...
51
52
53
54
55
...
»

Содержание 16533A

























































































































































Отзывы:

Нет отзывов