HP 16533A Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 152

HP 16533A Скачать руководство пользователя страница 82

Immediate Trigger Mode

When you are set up in a multi-card configuration, only the master
card input channels are recognized as the trigger source. The
oscilloscope will not trigger on inputs from the other cards in a
multi-card module.

This section discusses how immediate triggering works in a
single-card module or in the master card in a multi-card module.

Immediate trigger mode causes the oscilloscope to trigger by itself.
When you touch the Mode field, Immediate can be selected from the
pop-up menu.

Immediate trigger mode can be used for dual timebase (intermodule)
applications where, for instance, one oscilloscope module arms
another oscilloscope module, or another module (such as a logic
analyzer) arms the oscilloscope.

This mode is very similar to Auto-Trig On, but immediate mode does
not wait for a specified event to occur.

6-18

«
...
80
81
82
83
84
...
»

Содержание 16533A

























































































































































Отзывы:

Нет отзывов