Hoval TopGas 35 Скачать руководство пользователя страница 26

Страница: 26 / 36

4 213 893 / 01

COMMISSIONING

• If possibly a reduction of the water hardness we recom-

mend a complete desalination (no softening) with by-

pass, so that the sum of the alkaline-earths in the filling

water remains of approx. 0,5 mol/m

. During the filling

procedure the conductance of the filling water should

be supervised. This should be to approx. 10 µS/cm.

•

After filling the conductance of the plant water should

be between 50 and 200yS/cm. The pH value will adjust

itself thereby from initially 6,5 - 7,5 after some weeks

been in use on 8,0 - 8,5. If this should not be the ca se,

then specialized company for the water treatment is to

be assigned. This compa ny must as soon as the ad-

justment of the cor rect pH value has been completed

by inhibitors, which are suitable for aluminum materials

also regularly check the inhibitor concentration and the

pH value.

5.3.1 Filling up the system

- Old and new plants have to be rinsed and cleaned pro-

fessionally before filling up.

Filling or refilling of the plant: Demands on the fill-up

and make-up water according to (chapter 5.3) have to

be observed. During the lifetime of the heat production

plant the maximum water content (sum of fill-up and

make-up water) shouldn‘t exceed the triple of the maxi-

mum fill-up quantity.

Example: maximum fill-up quantity (as in table 1)

1600 l, maximum fill-up and make-up water content dur

ing lifetime 4800 l.

- Filling up the syphon at the condensation drain of the

boiler.

WARNING

Before commissioning, the siphon must be

filled with water to prevent flue gas leakage.

- Minimum system pressure at the boiler:

Type

TopGas

(35,45,60)

Minimum system pressure at the boiler

1,5 bar

The unit needs to be filled up slowly at the fill-up and drain

cock on the boiler, while the radiators are open.

NOTICE

System corrosion and bleeding problems are

often caused by refilling or topping up. Drain

trap at the condensate drain must be filled

with water.

5.4

Gas adjustment

Compliance with the maximum permissible

limit values for CO and NOx must be verified

through measurement at the installation loca-

tion.

5.4.1 Bleeding the gas pipeline

Open the gas shut-off value and bleed the air from the

pipeline up to the gas fitting; comply with the relevant reg-

ulations.

5.4.2 Commissioning

Place the boiler in operation according to the detailed op-

erating instructions.

5.4.3 Gas inlet pressure

The minimum flow pressure in the appliance connection

pipeline must attain the following values:

Natural gas = min. 18 mbar

max. 50 mbar

Propane

= min. 42,5 mbar max. 57,5 mbar

If the connection pressure for natural gas is below 15 or

above 50 mbar, no setting and no commissioning is to

take place.

5.4.4 Gas fitting

The Hoval TopGas

is equipped with a Honeywell pneu-

matic modulating multiple setting device. scope of supply

includes two solenoid valves (B+B), a screen filter plus an

installed pressure balance (1:1) - gas/air servo controller.

The fan which is activated by the boiler electrical sys-

tem produces a speed dependent air flow. This creates a

pressure drop in a venturi tube. The air pressure is trans-

ferred to the servo controller of the multiple setting device

where it brings about a pressure-proportional change in

the gas flow rate. The gas flow follows the air flow in the

given ratio (constant air factor in the modulation range).

Содержание TopGas 35





































Результаты поиска

Содержание TopGas 35

Отзывы:

Похожие инструкции для TopGas 35

Бренды по названию

Популярные бренды

Hoval TopGas 35, Техническая информация Инструкции по установке

Результаты поиска

Содержание TopGas 35

Отзывы:

Похожие инструкции для TopGas 35

Бренды по названию

Популярные бренды