Hoval TopGas 35 Скачать руководство пользователя страница 23

Страница: 23 / 36

4 213 893 / 01

MONTAGE

4.5.7 Connection of the pipes

On of the boiler installation the pipelines are connected

directly to the feed and the return connectors. Please

note the designations for the pipeline connectors in chap-

ter 3.3.

4.5.8 Condensate draining and neutralisation

The condensate from heat output gas boilers is to be

transferred to the public drainage system or an own

drainage system and where prescribed, neutralised prior

to introduction.

Please comply with the instructions of the re-

sponsible local waste water authorities.

In Austria:

Please note the planning directives for heat output firing

systems in the Austrian Standard H 5152 and in particular

the ÖVGW (G 41).

It is important, already prior to planning and executing

the boiler system to contact the responsible authorities to

plan and execute the condensate drainage according to

regulations.

The siphon drain pipe must be directed into

a funnel.

Fig. 10

4.5.9 Gas connection

WARNING

The installation of the gas pipeline and first

placing in operation must be carried out by a

recognised expert.

The provisions of the relevant national regulations

(SVGW directives, ÖVGW directives, DVGW-TRGI 86-

96, DIN 4750) as well as local regulations of gas supply

en terprises should be observed.

A manually operated shut-off device (gas shut-off cock)

in accordance with the local regulations is to be installed

directly before the boiler.

Please ask your local gas supply authority whether it is

necessary for an approved gas filter to be installed be

tween the manual shut-off valve and the boiler, to elimi

nate faults due to particles carried in the gas.

In Germany some regional building regulations require

the installation of a thermally activated shut-off valve di-

rectly before the boiler. Please enquire at your local re-

gional planning office.

WARNING

It is imperative to check all gas-carrying pipe-

lines for leaks before initially placing the boil-

er in operation.

4.6

Electrical connection

WARNING

The heat generator can only be de-energised

by disconnection from the mains (e.g. all-

pole switch).

WARNING

All electric power supply circuits must be

switched off before accessing the terminals.

WARNING

The electrical connection (sensors, pumps

and all other devices and components to be

connected) must be connected in accord-

ance with the applicable standards of nation-

ally or internationally recognised profession-

al associations.

Содержание TopGas 35





































Результаты поиска

Содержание TopGas 35

Отзывы:

Похожие инструкции для TopGas 35

Бренды по названию

Популярные бренды

Hoval TopGas 35, Техническая информация Инструкции по установке

Результаты поиска

Содержание TopGas 35

Отзывы:

Похожие инструкции для TopGas 35

Бренды по названию

Популярные бренды