manualshive.com logo in svg

Hoval TopGas 35, Техническая информация Инструкции по установке, Страница: 29 / 36

Поделиться
Скачать
Hoval TopGas 35 Скачать руководство пользователя страница 29

29

4 213 893 / 01

DECOMMISSIONING / MAINTENANCE

6. 

Decommissioning

The following steps are to be taken if the compact 

heat ing controller is to be placed out of operation for 

several weeks:

Clean the boiler heating surfaces and have your boiler 

servicing agent apply a conservation agent. Your chim-

ney-sweep technician will eagerly consult you.

Where there is a frost hazard, drain your system in ac

-

cordance with the instructions of your heating installer 

or add frost according to the instructions of the heating 

installer.

7. 

Maintenance

!

CAUTION

Missing or faulty cleaning and maintenance 

may cause damage to the installation.

•  The heating installation must be surveyed 

and cleaned once a year.

• 

If  required,  installation  maintenance  must 

be carried out. Defects must be remedied 

immediately in order to prevent damages 

to the installation!

!

CAUTION

After repair work respectively ex chang ing boil-

er parts, a flue gas meas urement according to 

chapter 5.4.5 must be carried out im per atively.

7.1 

Checking the water connections for leakage

Tighten screw connections on the water side while the 

boiler is still at operating temperature.

7.2 

Refilling

Water must be refilled, if the water pressure falls below 

the set flow pressure.

Then  allow  the  heating  water  to  cool,  bleed  the  filling 

hose and refill via the filling and draining cock.

7.3 

Maintenance includes

 -

Cleaning the flue gas heat exchanger 

 

and condensate collector

 - Checking the burner

 -

Checking  the  ignition  electrode,  distance  from  burner 

ap prox. 4-5 mm, set position correctly where necessary 

or replace

 - Flue gas measuring according to chapter 5.4.5

7.4 

Cleaning the heat exchanger

 - Disconnect the boiler from the electrical supply  

(pull out the plug)

 - Close the gas appliance cock

 -

Remove the front boiler panel (open the control flap lid, 

push the front cover upwards and pull out)

 - Unscrew the threaded of the supply pipeline to the gas 

solenoid valve (Fig. 15, see next page)

 - Detach the screw mounted burner plate (Fig. 15)

 - Disconnect the electrical connections to the gas sole-

noid valve

 - Pull off the fan connector plug

 - Remove the burner plate and bat-wing burners  

(Fig. 17, see next page)

 - Wet clean the heat exchanger (do not use steel wire 

brushes) (Fig. 17, see next page)

 -

Clean siphon (Fig. 13 and Fig. 14, below)

 -

Loosen siphon at coupling and remove from boiler

 - Rinse siphon.

 - Check if siphon sealing gasket Fig. 14 (1) is not dam-

aged, replace if necessary

 - Flue gas measuring according to chapter 5.4.5

!

CAUTION

If siphon is not filled with water or if it is con

-

taminated  or  obstructed  by  contamination, 

leaking flue gas may put people in danger of 

life.

• 

Before  reinserting  the  siphon,  it  must  be 

filled with water.

Siphon is fixed underneath the boiler!

Fig. 13

(1)

Fig. 14

Содержание TopGas 35





































Отзывы:

Нет отзывов