Hoval TopGas 35 Скачать руководство пользователя страница 4

Страница: 4 / 36

4 213 893 / 01

IMPORTANT INFORMATION

Important Information

BThe following points must be observed when performing

work on the TopGas

CAUTION

•

If you smell flue gas or gas,

•

avoid naked flames and

the occurrence of sparks,

•

do not smoke,

•

take the system out of operation,

•

close the gas shut-off valve,

• open windows and doors

• The system may only be placed in operation if all the

relevant standards and safety regulations have been

complied with. However, for trial operation, the follow

ing are the minimum conditions requiring fulfilment:

- Safety valve installed (closed system)

- Control in operation

(connected to the mains current supply system)

System filled with water

- Expansion tank connected

Boiler connected to a flue gas conduit installed

in compliance with the relevant regulations

- Burner preset

• When performing maintenance and repairs:

- Allow the gas condensing boiler to cool down

- Switch off the gas condensing boiler

and disconnect it from the power supply

- Close the gas shut-off valve

- Close all cut-off valves on the unit

(cold water, heating flow and return)

- If work on the components of the gas condensing

boiler which carry water is not performed correctly,

the heating medium may escape and lead to scald-

ing.

After performing repair and maintenance work,

reattach all cover plates which were removed.

- Do not exceed the maximum operating pressure and

operating temperature (see type label) for the gas

condensing boiler.

- Open all cut-off valves on the unit

(cold water, heating flow and return)

- Open gas shut-off valve

WARNING

The heat generator can only be de-energised

by disconnection from the mains (e.g. all-

pole switch).

WARNING

All electric power supply circuits must be

switched off before accessing the terminals.

1.1

On delivery

Carry out a visual inspection immediately on receiving the

boiler. If any damage is found, take the necessary steps

as defined in the delivery contract. The respective risk

carrier bears the cost of repairs.

1.2

Guarantee

The warranty does not cover defects attributable to:

- Failure to comply with these instructions

- Failure to comply with the operating instructions

- Incorrect installation

Impermissible modifications

- Incorrect handling

- Contaminated operating materials

(gas, water, combustion air)

- Unsuitable chemical additives to the heating water

- Damage caused by the application of force

- Corrosion by halogen compounds

(e.g. paints, adhesives, solvents)

- Corrosion caused by not observing

the required water quality

1.3

Instructions

All instructions relevant to your system can be found in

the Hoval system manual! In exceptional cases, the in

structions can be found with the components!

Further sources of information:

- Hoval catalogue

Standards, regulations

Содержание TopGas 35





































Результаты поиска

Содержание TopGas 35

Отзывы:

Похожие инструкции для TopGas 35

Бренды по названию

Популярные бренды

Hoval TopGas 35, Техническая информация Инструкции по установке

Результаты поиска

Содержание TopGas 35

Отзывы:

Похожие инструкции для TopGas 35

Бренды по названию

Популярные бренды