Honda HRR216VKA K10 Скачать руководство пользователя страница 19

Страница: 19 / 183

2-8

SERVICE INFORMATION

HRR216VKA

3. Verify the transmission control arm moves when rotating

the Smart Drive control.

• If the control arm does not move, see “SMART DRIVE

DISASSEMBLY AND INSPECTION” on

page 11-23

• If the control arm moves, adjust the Smart Drive cable

(see “CABLE ADJUSTMENT” on

page 3-10

(K5 ~ K7) TRANSMISSION PROPELS THE MOWER, BUT SLIPS OR SLOWS DOWN
UNDER LOAD

1. Adjust the Smart Drive cable (

P. 3-10

2. Have an assistant engage the Smart Drive control while

you inspect the transmission control arm position.

If the control arm contacts the transmission case as
shown, the clutch is worn and transmission replacement
is necessary.

3. Position the mower on a smooth concrete surface.

4. Start the engine and firmly engage the Smart Drive

control while holding the lawn mower from moving
forward. The rear wheels should spin (slip) on the
concrete surface.

If the wheels intermittently stop and/or a clicking sound
can be heard, inspect the pinion gears and ratchets
(

page 2-11

If both wheels stop, but no ratcheting or clicking sound
can be heard, the clutch may be worn and transmission
replacement is necessary.

Confirm the transmission control

arm moves when rotating the Smart

Drive control.

No contact between the control arm

and transmission case with the

Smart Drive control engaged.

CONTROL
ARM

Hold the mower from moving forward

and engage the Smart Drive control

on a smooth concrete surface.

Содержание HRR216VKA K10
























































































































































































Результаты поиска

Содержание HRR216VKA K10

Отзывы:

Похожие инструкции для HRR216VKA K10

Бренды по названию

Популярные бренды

Honda HRR216VKA K10, Руководство пользователя

Результаты поиска

Содержание HRR216VKA K10

Отзывы:

Похожие инструкции для HRR216VKA K10

Бренды по названию

Популярные бренды