Honda HRR216VKA K10 Скачать руководство пользователя страница 111

Страница: 111 / 183

10-2

CAM PULLEY/CRANKSHAFT/PISTON/ CYLINDER BLOCK

HRR216VKA

CAM PULLEY DECOMPRESSOR INSPECTION

1. Rotate the flywheel until the cam pulley decompressor

weight slot faces out.

2. Carefully inspect the weight position and confirm that it is

fully retracted. If it is not fully retracted, replace the cam
pulley

(P. 10-1)

3. If the weight is fully retracted, operate the decompressor

by very slowly moving it to the opposite end of the slot
and gently releasing. Repeat several times. If the weight
fails to completely return on its own at any time (by spring
force), replace the cam pulley

(P. 10-1)

CAM PULLEY INSTALLATION

1. Turn the crankshaft so that the long crankshaft key

groove (PTO side) faces up as shown.
The two woodruff key grooves will face down.

2. Install the cam pulley on the timing belt so that the cam

pulley alignment marks are in line with the cylinder head
cover mating surface.

Install the cam pulley on the timing belt with care not to
turn the crankshaft.

3. Apply oil to a new O-ring and install it on the cam pulley

shaft.

4. Install the cam pulley shaft in the cylinder block.

5. Hold the cam pulley alignment marks in line with the

cylinder head cover mating surface. Check again that the
crankshaft key groove is facing up.

6. If the key groove is not facing up, repeat the procedure

from step 1.

DECOMPRESSOR WEIGHT

ALIGNMENT

MARKS

CAM PULLEY

CYLINDER

HEAD COVER

MATING

SURFACE

WOODRUFF KEY GROOVE (2)

VIEW FROM PTO SIDE

LONG KEY

GROOVE

TIMING BELT

CAM PULLEY

SHAFT

O-RING,

6.8 x 1.9 mm



Содержание HRR216VKA K10
























































































































































































Результаты поиска

Содержание HRR216VKA K10

Отзывы:

Похожие инструкции для HRR216VKA K10

Бренды по названию

Популярные бренды

Honda HRR216VKA K10, Руководство пользователя

Результаты поиска

Содержание HRR216VKA K10

Отзывы:

Похожие инструкции для HRR216VKA K10

Бренды по названию

Популярные бренды