Honda HRR216VKA K10 Скачать руководство пользователя страница 74

Страница: 74 / 183

7-3

HRR216VKA

RECOIL STARTER

Starter Rope Broken Or Reel Unwound

1. Turn the starter reel in the direction of the arrow six turns.

Align the rope hole in the starter case with the rope hole in
the starter reel.

2. Pass the starter rope through the starter grip and make a

knot at the end of the rope.

3. Pass the other end of the starter rope through the rope

hole in the starter case and through the rope hole in the
starter reel, and make a slip knot at the end of the rope.

4. Remove the band holding the starter reel and carefully

allow the starter reel to rewind.

5. Check the operation of the ratchets by pulling the starter

rope several times.

STARTER REEL

STARTER CASE

ALIGN

HOLES

STARTER

REEL

STARTER GRIP

STARTER

ROPE

RATCHETS

Содержание HRR216VKA K10
























































































































































































Результаты поиска

Содержание HRR216VKA K10

Отзывы:

Похожие инструкции для HRR216VKA K10

Бренды по названию

Популярные бренды

Honda HRR216VKA K10, Руководство пользователя

Результаты поиска

Содержание HRR216VKA K10

Отзывы:

Похожие инструкции для HRR216VKA K10

Бренды по названию

Популярные бренды