Honda HRR216VKA K10 Скачать руководство пользователя страница 145

Страница: 145 / 183

11-16

HANDLE PIPE/CABLES/SMART DRIVE

HRR216VKA

10. Put a protective pad around the upper handle pipe. Tip

the mower up and secure the upper handle pipe in a
bench vise.

11. Remove the belt cover and drive belt (

P. 4-4

12. Rotate the transmission 180° as shown.
13. Using pliers, pinch the Smart Drive cable locks, pull on

the cable, and remove it from the cable holder.

14. Lift the Smart Drive cable wire through the slot in the

cable holder and remove the cable end from the
transmission control arm.

15. Remove the Smart Drive cable from the lawn mower.

INSTALLATION

1. Route the Smart Drive cable down through the hole in

the cutter housing.

2. Attach the Smart Drive cable end on the transmission

control arm.

3. Align the Smart Drive cable wire with the cable holder

slot and install the snap fitting into the cable bracket.

4. Reinstall the belt tensioner spring and drive belt

(

P. 4-5

5. If installing a new Smart Drive cable, fully loosen the

cable adjuster before installing the new Smart Drive
cable.

6. Route the upper end of the Smart Drive cable through

the hole in the handle pipe until it's visible in the slot in
the top of the handle pipe.

CABLE
HOLDER

CABLE
LOCKS

TRANSMISSION
CONTROL ARM

SMART
DRIVE
CABLE
WIRE

SMART
DRIVE
CABLE
END

CABLE HOLDER
SLOT

CUTTER
HOUSING
HOLE

SNAP
FITTING

CABLE
END

SMART
DRIVE
CABLE

HANDLE
PIPE
SLOT

Содержание HRR216VKA K10
























































































































































































Результаты поиска

Содержание HRR216VKA K10

Отзывы:

Похожие инструкции для HRR216VKA K10

Бренды по названию

Популярные бренды

Honda HRR216VKA K10, Руководство пользователя

Результаты поиска

Содержание HRR216VKA K10

Отзывы:

Похожие инструкции для HRR216VKA K10

Бренды по названию

Популярные бренды