Honda HRR216VKA K10 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 183

background image

2-26

SERVICE INFORMATION

HRR216VKA

CHOKE CONTROL SYSTEM (ACS) (K5 ~ K7)

With the engine cold,
remove the paper
element and check the
choke valve.

Remove the carburetor. Turn and
hold the choke arm in the choke
CLOSED position. Push the choke
valve open, and let it go. Check that
the choke valve snaps back to the
choke CLOSED position.

Replace the carburetor.

Partially

or totally

open

Not

normal

Check the choke valve for freedom
of movement.

Closed

Start the engine and
check to see if the
choke flutters and
opens as the engine
warms up.

Flutters

Does not

flutter

Replace the choke control
assembly.

Replace the carburetor
assembly.

Normal

Moves freely

System operates normally.

Replace the choke
control assembly.

See if the choke valve
opens after 5-8 minutes
(opening time will vary
based on load and
ambient temperature).

Choke
opens
fully

System operates
normally.

Does not

open or

opens
slowly

Does not open:

Check that the ACS control is installed
correctly. The choke lever tab may be on
the wrong side of the carburetor choke
lever post, which will cause the choke to
remain closed.
If the ACS is installed correctly, replace
the carburetor assembly (

.

Opens slowly:

• (K5 only) Apply Hondabond HT to heat sink and push heat sink against

cylinder barrel to ensure good heat transfer

.

• (K6~K7) Replace the thermowax (

• Be sure a BPR5ES spark plug is installed and not the cooler BPR6ES

plug. The BPR5ES is less susceptible to fouling on ACS equipped
engines.

CHOKE

LEVER

TAB

CARBURETOR CHOKE

LEVER POST

Hard to

move

SERVICE REMINDER #3 =>

«
...
35
36
37
38
39
...
»

Содержание HRR216VKA K10
























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HRR216VKA K10

Бренд: Cub Cadet Страницы: 56

GLM 40/124 P EASY

Бренд: F.F. Group Страницы: 128

Бренд: Rally Страницы: 24

Бренд: Gardena Страницы: 18

Бренд: Sentinel Страницы: 40

Бренд: Bad Boy Страницы: 36

Бренд: MTD Страницы: 16

Бренд: QuadBoss Страницы: 16

Бренд: AL-KO Страницы: 20

Бренд: S.E.P. Страницы: 20

Бренд: bannerman Страницы: 11

Бренд: OHIOSTEEL Страницы: 14

Бренд: Kraftixx Страницы: 246

Бренд: Husqvarna Страницы: 18

Бренд: Husqvarna Страницы: 42

Бренд: Husqvarna Страницы: 44

Z6029FX/966061201

Бренд: Husqvarna Страницы: 44

Бренд: Husqvarna Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды