Honda HRR216VKA K10 Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 183

background image

8-25

HRR216VKA

FUEL SYSTEM

REMOVAL/INSTALLATION (K9 thru K11)

1. Before removal, drain the gasoline into an approved container.
2. Remove the recoil starter and the fan cover.
3. Remove the fuel tube from the fuel tank.
4. Remove the fuel tank cap from the fuel tank. Unscrew the tether from the fuel filler threads.
5. Unscrew the tank mount nut from the fuel filler threads and turn the fan cover over.
6. Press the latch on the tank mount clip as shown below and remove the clip, and then remove the fuel tank from

the fan cover.

7. Fuel tank installation is the reverse of its removal.

FUEL TANK CAP

OPERATION

:



WARNING

Gasoline is highly flammable and explosive.
You can be burned or seriously injured when handling fuel.
•

Stop the engine and let it cool.

•

Keep heat, sparks, and flame away.

•

Handle fuel only outdoors.

•

Wipe up spills immediately.

FAN COVER

INSTALLATION:

Check that the high-tension cord

is securely set in the groove in

the fan cover as shown.

HIGH-TENSION CORD

FUEL TANK

INSTALLATION:

Wash with solvent to remove the

sediment, and dry thoroughly before

installation.

INSPECTION:

FUEL FILLER NECK SEAL

TANK SIDE

FUEL TUBE

REMOVAL/INSTALLATION:

INSPECTION:

Inspect for cracks or

deterioration before installation, and

replace if necessary.

TANK MOUNT CLIP

PRESS HERE TO RELEASE

TUBE CLIP (2)

TANK MOUNT RUBBER A

8.5 mm

(0.33 in)

TANK MOUNT RUBBER B

13.5 mm

(0.5 in)

FUEL STRAINER

TETHER

TANK MOUNT NUT

Gently
tighten the
new tank
mount nut,
using
tongue and
groove
pliers, until
the
alignment
mark is in
the
position
shown.

TANK

MOUNT NUT

ALIGNMENT

MARK

ALIGNMENT POSITION

MARK RANGE

«
...
98
99
100
101
102
...
»

Содержание HRR216VKA K10
























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HRR216VKA K10

Бренд: Jacobsen Страницы: 58

Бренд: Jacobsen Страницы: 106

Бренд: Jacobsen Страницы: 60

Бренд: Jacobsen Страницы: 58

Бренд: Jacobsen Страницы: 118

Бренд: Jacobsen Страницы: 160

Бренд: Jacobsen Страницы: 20

Бренд: Jacobsen Страницы: 30

Greens King IV Plus

Бренд: Jacobsen Страницы: 60

Greens King IV Plus

Бренд: Jacobsen Страницы: 32

Ransomes HR 6010

Бренд: Jacobsen Страницы: 76

Бренд: Jacobsen Страницы: 48

Бренд: Jacobsen Страницы: 76

Бренд: Jacobsen Страницы: 76

Бренд: Jacobsen Страницы: 144

AR-522 jossa ROPS

Бренд: Jacobsen Страницы: 56

AR-522 jossa ROPS

Бренд: Jacobsen Страницы: 115

Бренд: Jacobsen Страницы: 130

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды