Honda BF250A Скачать руководство пользователя страница 97

Страница: 97 / 139

TAKING CARE OF UNEXPECTED PROBLEMS

ENGINE WILL NOT START

Possible Cause

Correction

Battery connections loose or corroded.

Clean and tighten battery connections.

Battery discharged.

Recharge battery.

Fuse(s) blown.

Replace fuse(s) (p. 98).

Spark plugs faulty, fouled, or improperly gapped.

Gap or replace spark plugs (p. 70).

Spark plugs wet with fuel (flooded engine).

Dry and reinstall spark plugs. Start engine with the throttle

open.

Fuel system malfunction, fuel pump failure, ignition

malfunction, stuck valves, starter malfunction, switch

malfunction, or electrical problem in the starting circuit,

etc.

Use starting procedure (p. 40, 43, 45); if engine still will

not start, then take outboard motor to an authorized Honda

Marine dealer, or refer to the shop manual.

31ZX26040.book Page 95 Friday, July 25, 2014 5:14 PM

Содержание BF250A












































































































































Результаты поиска

Содержание BF250A

Отзывы:

Honda BF250A, Руководство пользователя, Страница: 97 / 139

Результаты поиска

Содержание BF250A

Отзывы: