Honda BF250A Скачать руководство пользователя страница 81

Страница: 81 / 139

SERVICING YOUR OUTBOARD MOTOR

Water Separator Inspection and

Service

The water separator is located under

No. 6 cylinder ignition coil. Water

accumulation in the water separator

can cause loss of power or hard

starting. Check the water separator

periodically. Clean it or consult with

an authorized Honda Marine dealer

for cleaning.

<Cleaning>

1. Remove the engine cover (p. 63).

2. Remove the plug maintenance

cover (p. 70).

3. Remove the cover under the idle

port.

4. Remove the left under cover by

removing the 6 × 17 mm special

bolts.

No.6 CYLINDER IGNITION COIL

WATER SEPARATOR

Gasoline is highly flammable and

explosive.

You can be burned or seriously

injured when handling fuel.

• Stop the engine and keep heat,

sparks, and flame away.

• Handle fuel only outdoors.

• Wipe up spills immediately.

6 × 17 mm SPECIAL BOLTS

6 × 17 mm

SPECIAL BOLTS

IDLE

PORT

LEFT UNDER

COVER

31ZX26040.book Page 79 Friday, July 25, 2014 5:14 PM

Содержание BF250A












































































































































Результаты поиска

Содержание BF250A

Отзывы:

Honda BF250A, Руководство пользователя, Страница: 81 / 139

Результаты поиска

Содержание BF250A

Отзывы: