manualshive.com logo in svg

Honda BF250A, Руководство пользователя, Страница: 104 / 139

Поделиться
Скачать
Honda BF250A Скачать руководство пользователя страница 104

102

TAKING CARE OF UNEXPECTED PROBLEMS

If the throttle is closed suddenly after 

full throttle operation, engine speed 

may drop below the specified idle 

rpm, and that could activate the 

engine protection system 

momentarily.

If low oil pressure activates the 

engine protection system, stop the 

engine, check the engine oil level 

(p. 64), and add oil if needed.

With the engine oil at the 

recommended level, restart the 

engine. If the lubrication system is 

OK, the oil pressure indicator should 

come on within 30 seconds, and the 

engine will respond normally to 

throttle control lever operation.

If the engine protection system 

remains activated after 30 seconds, 

return to the nearest boat landing, and 

have the outboard motor inspected by 

an authorized Honda Marine dealer.

OVERHEAT INDICATOR 

COMES ON AND ENGINE 

SPEED IS LIMITED

If the engine overheats, the overheat 

indicator will come on, and the 

engine will stop in 20 seconds after 

the engine protection system limits 

engine speed. If you are at cruising 

speed, engine speed will decrease 

automatically.

All types are equipped with a buzzer 

that sounds when the overheat 

indicator comes on.

Engine overheating may be the result 

of restricted water intake screens, or 

there may be a problem with the 

cooling system thermostat or water 

pump.

BUZZER

BUZZER

OVERHEAT 

INDICATOR

(RED)

OVERHEAT 

INDICATOR

(RED)

Panel-Mount/Top-Mount Types

Side-Mount Type

31ZX26040.book  Page 102  Friday, July 25, 2014  5:14 PM

Содержание BF250A












































































































































Отзывы:

Нет отзывов