manualshive.com logo in svg

Honda BF250A, Руководство пользователя, Страница: 80 / 139

Поделиться
Скачать
Honda BF250A Скачать руководство пользователя страница 80

78

SERVICING YOUR OUTBOARD MOTOR

2. Before removing the fuel filter, to 

prevent fuel leakage, place 

commercially available fuel hose 

clips on the fuel hoses on each side 

of the fuel filter.

3. Disconnect the fuel hoses from the 

strainer body.

4. Unscrew the strainer cup from the 

strainer body.

5. Thoroughly clean the strainer cup, 

and install a new fuel filter.

6. Reassemble the strainer body and 

the cup using new O-rings.

STRAINER TIGHTENING 

TORQUE:

1.8 lbf·ft (2.5 N·m, 0.25 kgf·m)

7. Install the suspension strap to the 

fuel filter assembly.

8. Connect the fuel hoses to the fuel 

filter assembly with the hose 

clamps. Remove the fuel hose clips 

used to close the fuel hoses.

9. Align the center of the two fuel 

hoses and the arrow of the 

suspension strap rib.

10. Reinstall the fuel filter assembly 

to the fuel filter bracket.

11. Prime the engine using the 

priming bulb (p. 39). Check for 

fuel leaks.

Repair any fuel leaks if necessary.

If loss of power or hard starting are 

found to be caused by excessive 

water or sediment accumulation in 

the fuel filter, inspect the fuel tank.

Clean the fuel tank and tank filter if 

necessary. It may be necessary to 

drain the fuel tank completely and 

refill with fresh gasoline.

FUEL FILTER BRACKET

SUSPENSION STRAP

FLOAT

FUEL 

FILTER

STRAINER 

CUP

O-RINGS 

(Replace)

STRAINER BODY

FUEL HOSES

FUEL 

HOSE 

CLIPS

ARROW

SUSPENSION STRAP RIB

FUEL HOSES

31ZX26040.book  Page 78  Friday, July 25, 2014  5:14 PM

Содержание BF250A












































































































































Отзывы:

Нет отзывов