Honda BF250A Скачать руководство пользователя страница 102

Страница: 102 / 139

100

TAKING CARE OF UNEXPECTED PROBLEMS

7. Close the junction box cover and

reinstall the engine cover (p. 63).

8. Reconnect the battery.

Never use a fuse with a rating greater

than specified. Serious damage to the

electrical system could result.

If a blown fuse is found, try to

determine and correct the electrical

problem that caused the blown fuse.

An uncorrected electrical problem

may cause the fuse to blow again.

If fuses continue to blow, take the

outboard motor to an authorized

Honda Marine dealer for inspection

and service, or refer to the shop

manual.

ACG Fuse

Replacement

1. Stop the engine.

2. Disconnect the battery.

3. Remove the engine cover (p. 63).

4. Open the junction box cover.

5. Remove the old fuse by removing

two 5 mm screws.

6. Install a new fuse by tightening two

5 mm screws.

ACG FUSE: 150 A

7. After finishing replacement, close

the junction box cover.

8. Install the engine cover (p. 63).

9. Reconnect the battery.

JUNCTION

BOX COVER

5 mm SCREWS

ACG FUSE

(150 A)

SPARE FUSE (150 A)

PAWLS

31ZX26040.book Page 100 Friday, July 25, 2014 5:14 PM

Содержание BF250A












































































































































Результаты поиска

Содержание BF250A

Отзывы:

Honda BF250A, Руководство пользователя, Страница: 102 / 139

Результаты поиска

Содержание BF250A

Отзывы: