Honda BF250A Скачать руководство пользователя страница 109

Страница: 109 / 139

107

TECHNICAL INFORMATION

Battery

For complete information, refer to the

battery manufacturer’s instructions.

Minimum Requirements

12 V – 92 Ah/5 HR (110 Ah/20 HR)

(CCA800)

• Be careful to avoid connecting the

battery in reverse polarity, as this

will damage the battery-charging

system in the outboard motor.

• Do not disconnect the battery

cables while the engine is running.

Disconnecting the cables while the

engine is running will damage the

outboard motor’s electrical system.

• Battery cable extension: Extending

the original battery cable will

cause the battery voltage to drop

due to the increased length of the

cable and number of connections.

This voltage drop may cause the

buzzer to sound momentarily when

engaging the starter motor and

may prevent the engine from

starting. If the engine starts and the

buzzer sounds momentarily, there

may be barely sufficient voltage

reaching the engine.

WARNING:

Battery posts,

terminals, and related accessories

contain lead and lead compounds.

Wash your hands after handling.

31ZX26040.book Page 107 Friday, July 25, 2014 5:14 PM

Содержание BF250A












































































































































Результаты поиска

Содержание BF250A

Отзывы:

Honda BF250A, Руководство пользователя, Страница: 109 / 139

Результаты поиска

Содержание BF250A

Отзывы: