Honda BF250A Скачать руководство пользователя страница 120 | Manualshive

Страница: 120 / 139

Honda BF250A Скачать руководство пользователя страница 120

118

CONSUMER INFORMATION

Warranty Statements

The American Honda Distributor’s Limited Warranty applies to outboards purchased in the United States, Puerto Rico,

or the U.S. Virgin Islands. The Honda Canada Distributor’s Warranty applies to outboards purchased in Canada.

The product warranty is only valid in the country where the product was purchased.

United states, Puerto Rico and Virgin Islands

Distributor’s Limited Warranty

This warranty is limited to Honda Outboard Motors and related original equipment distributed by American Honda

Motor Co., Inc., Power Equipment Division, 4900 Marconi Drive, Alpharetta, Georgia 30005-8847.

(1) Models purchased prior to July 1, 2008 (unless previously purchased with True-5 warranty from a participating dealer).

(2) 35, 65, & 105 Jet models: Jet pump assembly is a dealer installed option. Jet pump warranty is provided by Specialty Manufacturing Co. (Outboard Jets).

Products Covered by Warranty:

Length of Warranty: (from date of original retail purchase)

NONCOMMERCIAL/

NONRENTAL

COMMERCIAL/RENTAL STATE/LOCAL/FEDERAL

GOVERNMENT

All models purchased before July 1, 2008

(1) (2)

36 months

12 months

24 months

All Models purchased on or after July 1, 2008

(2)

60 months

12 months

24 months

Related original equipment items:
BF2 through BF30 models: Portable fuel tank and
original propeller.
All models: Primer bulb/fuel line assembly and
tiller handle.

The same duration as the outboard with which they were purchased.

31ZX26040.book Page 118 Friday, July 25, 2014 5:14 PM

«
...
118
119
120
121
122
...
»

Содержание BF250A












































































































































Отзывы:

Нет отзывов