Honda BF250A Скачать руководство пользователя страница 65

Страница: 65 / 139

SERVICING YOUR OUTBOARD MOTOR

MANUAL RELIEF VALVE

The outboard motor can be tilted

manually after opening the manual

relief valve. This feature enables the

outboard motor to be tilted up or

down when no battery is connected.

For manual tilting, use a screwdriver

to turn the valve counterclockwise 1

or 2 turns. Close the valve firmly

after positioning the outboard motor.

Be sure the valve is closed before

operating the outboard motor. If the

valve is not closed, the outboard

motor will tilt up when operated in

reverse.

ENGINE COVER REMOVAL

AND INSTALLATION

Removal

1. Pull the engine cover latch.

2. Remove the engine cover by lifting

it straight up from the outboard

motor.

Installation

1. Place the engine cover on the main

body.

2. Slide the engine cover so that the

cover lock on the cover aligns with

the lock in the main body.

MANUAL RELIEF VALVE

POWER

(To fix)

MANUAL

(To release)

ENGINE COVER LATCH

COVER SIDE

COVER LOCKS

MAIN BODY SIDE

31ZX26040.book Page 63 Friday, July 25, 2014 5:14 PM

Содержание BF250A












































































































































Результаты поиска

Содержание BF250A

Отзывы:

Honda BF250A, Руководство пользователя, Страница: 65 / 139

Результаты поиска

Содержание BF250A

Отзывы: