Honda BF250A Скачать руководство пользователя страница 41

Страница: 41 / 139

OPERATION

FUEL PRIMING

Hold the priming bulb up in the

direction of the arrow; then squeeze

the priming bulb several times until it

feels firm, indicating that fuel has

reached the engine.

Check to be sure there are no fuel

leaks before starting the engine.

Do not touch the priming bulb with

the engine running or when tilting up

the outboard motor. The vapor

separator could overflow.

INFREQUENT OR

OCCASIONAL USE

If your outboard motor will be used

on an infrequent or intermittent basis,

please refer to the fuel section of the

STORAGE

chapter (p. 87) for

additional information regarding fuel

deterioration.

OUTLET END

(outboard motor side)

PRIMING BULB

INLET END

(tank side)

Gasoline is highly flammable and

explosive.

You can be burned or seriously

injured when handling fuel.

• Stop the engine and keep heat,

sparks, and flame away.

• Handle fuel only outdoors.

• Wipe up spills immediately.

31ZX26040.book Page 39 Friday, July 25, 2014 5:14 PM

Содержание BF250A












































































































































Результаты поиска

Содержание BF250A

Отзывы:

Honda BF250A, Руководство пользователя, Страница: 41 / 139

Результаты поиска

Содержание BF250A

Отзывы: