Honda BF250A Скачать руководство пользователя страница 10

Страница: 10 / 139

OUTBOARD MOTOR SAFETY

Refuel With Care

• Gasoline is extremely flammable,

and gasoline vapor can explode.

Refuel outdoors, in a

well-ventilated area, with the

engine stopped. Never smoke near

gasoline, and keep other flames and

sparks away.

• Refuel carefully to avoid spilling

fuel. Avoid overfilling the fuel

tank.

• After refueling, tighten the fuel

tank cap securely. If any fuel is

spilled, make sure the area is dry

before starting the engine.

Carbon Monoxide Hazard

Exhaust contains poisonous carbon

monoxide, a colorless, odorless gas.

Breathing carbon monoxide can

cause loss of consciousness and may

lead to death.

If you run the engine in an area that is

confined, or even partly enclosed, the

air you breathe could contain a

dangerous amount of exhaust gas.

Never run your outboard inside a

garage or other enclosure.

31ZX26040.book Page 8 Friday, July 25, 2014 5:14 PM

Содержание BF250A












































































































































Результаты поиска

Содержание BF250A

Отзывы:

Honda BF250A, Руководство пользователя, Страница: 10 / 139

Результаты поиска

Содержание BF250A

Отзывы: