Holtek HT45F6530 Скачать руководство пользователя страница 65

Страница: 65 / 119

Rev. 1.00

August 29, 2018

Rev. 1.00

August 29, 2018

HT45F6530

AC Voltage Regulator Flash MCU

HT45F6530

AC Voltage Regulator Flash MCU

In the PWM Output Mode, the CTnIO1 and CTnIO0 bits determine how the CTMn

output pin changes state when a certain compare match condition occurs. The PWM

output function is modified by changing these two bits. It is necessary to only change

the values of the CTnIO1 and CTnIO0 bits only after the CTMn has been switched off.

Unpredictable PWM outputs will occur if the CTnIO1 and CTnIO0 bits are changed

when the CTMn is running.

Bit 3

CTnOC

: CTMn CTPn Output control

Compare Match Output Mode

0: Initial low

1: Initial high

PWM Output Mode/Single Pulse Output Mode

0: Active low

1: Active high

This is the output control bit for the CTMn output pin. Its operation depends upon

whether CTMn is being used in the Compare Match Output Mode or in the PWM

Output Mode. It has no effect if the CTMn is in the Timer/Counter Mode. In the

Compare Match Output Mode it determines the logic level of the CTMn output pin

before a compare match occurs. In the PWM Output Mode it determines if the PWM

signal is active high or active low.

Bit 2

CTnPOL

: CTMn CTPn Output polarity control

0: Non-invert

1: Invert

This bit controls the polarity of the CTPn output pin. When the bit is set high the

CTMn output pin will be inverted and not inverted when the bit is zero. It has no effect

if the CTMn is in the Timer/Counter Mode.

Bit 1

CTnDPX

: CTMn PWM duty/period control

0: CCRP – period; CCRA – duty

1: CCRP – duty; CCRA – period

This bit determines which of the CCRA and CCRP registers are used for period and

duty control of the PWM waveform.

Bit 0

CTCCLR

: CTMn Counter Clear condition selection

0: Comparator P match

1: Comparator A match

This bit is used to select the method which clears the counter. Remember that the

CTMn contains two comparators, Comparator A and Comparator P, either of which

can be selected to clear the internal counter. With the CTnCCLR bit set high, the

counter will be cleared when a compare match occurs from the Comparator A. When

the bit is low, the counter will be cleared when a compare match occurs from the

Comparator P or with a counter overflow. A counter overflow clearing method can

only be implemented if the CCRP bits are all cleared to zero. The CTnCCLR bit is not

used in the PWM Output mode.

• CTMnDL Register

Bit

Name

R/W

POR

Bit 7~0

D7~D0

: CTMn Counter Low Byte Register bit 7~bit 0

CTMn 10-bit Counter bit 7~bit 0

Содержание HT45F6530
























































































































Результаты поиска

Содержание HT45F6530

Отзывы:

Похожие инструкции для HT45F6530

Бренды по названию

Популярные бренды

Holtek HT45F6530, Руководство пользователя

Результаты поиска

Содержание HT45F6530

Отзывы:

Похожие инструкции для HT45F6530

Бренды по названию

Популярные бренды