Holtek HT45F6530 Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 119

background image

Rev. 1.00

78

August 29, 2018

Rev. 1.00

79

August 29, 2018

HT45F6530

AC Voltage Regulator Flash MCU

HT45F6530

AC Voltage Regulator Flash MCU

Summary of A/D Conversion Steps

The following summarises the individual steps that should be executed in order to implement an A/D
conversion process.

• Step 1

Select the required A/D conversion clock by correctly programming bits SACKS2~SACKS0 in
the SADC1 register.

• Step 2

Enable the A/D by setting the ADCEN bit in the SADC0 register to one.

• Step 3

Select which signal is to be connected to the internal A/D converter by correctly configuring the

SAINS3~SAINS0 bits in the SADC1 register.
Select the external channel input to be converted, go to Step 4.
Select the internal analog signal to be converted, go to Step 5.

• Step 4

If the A/D input signal comes from the external channel input selected by configuring the SAINS
bit field, the corresponding pins should be configured as A/D input function by configuring the

relevant pin-shared function control bits. The desired analog channel then should be selected by

configuring the SACS bit field. After this step, go to Step 6.

• Step 5

If the A/D input signal comes from the internal analog signal, the SAINS bit field should be
properly configured and then the external channel input will automatically be disconnected

regardless of the SACS bit field value. After this step, go to Step 6.

• Step 6

Select the reference voltage source by configuring the SAVRS1~SAVRS0 bits in the SADC2
register.

Select the PGA input signal and the desired PGA gain and enable the PGA if the PGA output

voltage, V

R

, is selected as the A/D converter reference voltage.

•

Step 7

Select A/D converter output data format by setting the ADRFS bit in the SADC0 register.

• Step 8

If A/D conversion interrupt is used, the interrupt control registers must be correctly configured

to ensure the A/D interrupt function is active. The master interrupt control bit, EMI, and the A/D
conversion interrupt control bit, ADE, must both be set high in advance.

• Step 9

The A/D conversion procedure can now be initialized by setting the START bit from low to high
and then low again.

• Step 10

If A/D conversion is in progress, the ADBZ flag will be set high. After the A/D conversion
process is complete, the ADBZ flag will go low and then the output data can be read from
SADOH and SADOL registers.

Note: When checking for the end of the conversion process, if the method of polling the ADBZ bit

in the SADC0 register is used, the interrupt enable step above can be omitted.

«
...
77
78
79
80
81
...
»

Содержание HT45F6530
























































































































Отзывы:

Нет отзывов

Похожие инструкции для HT45F6530

ShareCenter DNS-343

Бренд: D-Link Страницы: 12

Бренд: IBM Страницы: 301

Бренд: Lanner Страницы: 40

Бренд: Seville Classics Страницы: 7

Бренд: Hama Страницы: 8

Бренд: U.S. General Страницы: 2

RESU RESU10H Prime

Бренд: LG Страницы: 8

Бренд: LG Страницы: 21

Бренд: LG Страницы: 15

Бренд: LG Страницы: 1

Portable Theater HXF2

Бренд: LG Страницы: 48

Бренд: LG Страницы: 50

Бренд: LG Страницы: 1

WD Elements WDE1UBK10000

Бренд: Western Digital Страницы: 2

Бренд: QNAP Страницы: 39

Бренд: IBM Страницы: 208

Бренд: Rasilient Страницы: 43

Бренд: Beta Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды