manualshive.com logo in svg

Holtek HT45F4050, Руководство пользователя

Holtek HT45F4050 - микроконтроллер с возможностью загрузки бесплатных инструкций на русском языке. Скачайте нужное руководство с manualshive.com и начните использовать устройство по максимуму. Мануал доступен для загрузки в формате PDF, чтобы помочь вам с настройкой и управлением микроконтроллера.

Поделиться
Скачать
background image

Rev. 1.00

56

September 11, 2018

Rev. 1.00

57

September 11, 2018

HT45F4050

A/D NFC Flash MCU

HT45F4050

A/D NFC Flash MCU

Reset and Initialisation

A reset function is a fundamental part of any microcontroller ensuring that the device can be set 
to some predetermined condition irrespective of outside parameters. The most important reset 
condition is after power is first applied to the microcontroller. In this case, internal circuitry will 
ensure that the microcontroller, after a short delay, will be in a well-defined state and ready to 
execute the first program instruction. After this power-on reset, certain important internal registers 
will be set to defined states before the program commences. One of these registers is the Program 
Counter, which will be reset to zero forcing the microcontroller to begin program execution from the 
lowest Program Memory address. 
In addition to the power-on reset, situations may arise where it is necessary to forcefully apply 
a reset condition when the device is running. One example of this is where after power has been 
applied and the device is already running, the RES

 

line is forcefully pulled low. In such a case, 

known as a normal operation reset, some of the registers remain unchanged allowing the device

 to 

proceed with normal operation after the reset line is allowed to return high.
Another reset exists in the form of a Low Voltage Reset, LVR, where a full reset, similar to the RES

 

reset is implemented in situations where the power supply voltage falls below a certain threshold.

 

Another type of reset is when the Watchdog Timer overflows and resets the microcontroller. All 
types of reset operations result in different register conditions being setup.

Reset Functions

There are several ways in which a microcontroller reset can occur, through events occurring both 
internally and externally.

Power-on Reset

The most fundamental and unavoidable reset is the one that occurs after power is first applied to 
the microcontroller. As well as ensuring that the Program Memory begins execution from the first 
memory address, a power-on reset also ensures that certain other registers are preset to known 
conditions. All the I/O port and port control registers will power up in a high condition ensuring that 
all I/O ports will be first set to inputs.

Internal Reset

t

RSTD

+t

SST

0.9V

DD

RES

VDD

Power-On Reset Timing Chart

RES Pin Reset

Although the microcontroller has an internal RC reset function, if the V

DD

 power supply rise time 

is not fast enough or does not stabilise quickly at power-on, the internal reset function may be 
incapable of providing proper reset operation. For this reason it is recommended that an external 
RC network is connected to the RES

 

pin, whose additional time delay will ensure that the RES

 pin 

remains low for an extended period to allow the power supply to stabilise. During this time delay, 
normal operation of the microcontroller will be inhibited. After the RES

 

line reaches a certain 

voltage value, the reset delay time t

RSTD

 is invoked to provide an extra delay time after which the 

microcontroller will begin normal operation. The abbreviation SST in the figures stands for System 
Start-up Timer.

Содержание HT45F4050










































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HT45F4050

IBM TotalStorage DS4800 Installation, User And Maintenance Manual preview
TotalStorage DS4800
Бренд: IBM Страницы: 250
IBM TotalStorage DS4800 User, Installation And Maintenance Manual preview
TotalStorage DS4800
Бренд: IBM Страницы: 234
IBM T400 Setup, Operation, And Service Manual preview
T400
Бренд: IBM Страницы: 136
IBM System Storage DS5020 Overview preview
System Storage DS5020
Бренд: IBM Страницы: 31
IBM Netfinity EXP300 Hardware Maintenance Manual preview
Netfinity EXP300
Бренд: IBM Страницы: 93
IBM DS4700 EXPRESS Installation, User'S, And Maintenance Manual preview
DS4700 EXPRESS
Бренд: IBM Страницы: 270
IBM Ultrastar 36LZX Quick Installation Manual preview
Ultrastar 36LZX
Бренд: IBM Страницы: 2
IBM DCAS-32160 - Ultrastar 2.1 GB Hard Drive Specifications preview
DCAS-32160 - Ultrastar 2.1 GB Hard Drive
Бренд: IBM Страницы: 232
IBM System Storage TS3310 Maintenance Information preview
System Storage TS3310
Бренд: IBM Страницы: 531
Backyard Discovery GABLE Assembly Manual preview
GABLE
Бренд: Backyard Discovery Страницы: 72
PEAKnx PNX11-10010 Getting Started preview
PNX11-10010
Бренд: PEAKnx Страницы: 14
IAC INDUSTRIES Quick Ship ISLES WORKMASTER Assembly Instructions Manual preview
Quick Ship ISLES WORKMASTER
Бренд: IAC INDUSTRIES Страницы: 11
QNAP TS-h1886XU-RP-R2 User Manual preview
TS-h1886XU-RP-R2
Бренд: QNAP Страницы: 62
Addonics Technologies AEIDMD4U2 Installation Manual preview
AEIDMD4U2
Бренд: Addonics Technologies Страницы: 2
Swissbit iCCT User Manual preview
iCCT
Бренд: Swissbit Страницы: 11
Husky H4TR1 Use And Care Manual preview
H4TR1
Бренд: Husky Страницы: 7
LaCie 2big Thunderbolt Series 4 TB User Manual preview
2big Thunderbolt Series 4 TB
Бренд: LaCie Страницы: 45
IBM System Storage DCS Series Installation And Migration Manual preview
System Storage DCS Series
Бренд: IBM Страницы: 90

Бренды по названию

Популярные бренды

Загрузить еще бренды