HNP Mikrosysteme mzr-2542 Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 91

background image

7 The startup/shutdown of a pump

Operating manual mzr-2542 / mzr

-

2942

Last update: January 2016

Technical data subject to change without prior notice!

53

7.5

Problem shooting

If the pump does not start to operate or stops the operation abruptly, please
proceed as follows:

Try to liberate the micro annular gear pump:



by turning the potentiometer knob back and forth or by sending an analog
voltage signal



via the control software



through the micro annular gear pump



by changing the operating direction of the pump.

If these measures turn out to be ineffective, please contact the service staff of
HNP Mikrosysteme (see chapter 14) and send the pump back to the
manufacturer for inspection.

Warning

You should under no condition try to dismantle the pump by yourself. This
may cause damage to the pump components and consequently annul your
warranty claims.

7.6

Return of the micro annular gear pump to the manufacturer

For the return of a micro annular gear pump and components that have already
been employed, please follow the instructions:



drain any remaining rests of the delivered liquid from the pump



flush the pump with an adapted solvent



remove the filter elements from integrated or loosely delivered filters



protect all openings against dust with the delivered protective plugs or
screws



return the pump in its original packing

The service personnel which carries out the repair should be informed about
the condition of the used micro annular gear pump. This is done by means of
the "Declaration of media in contact with the micro annular gear pump and
components" (see chapter 14). This form may also be downloaded from the
web site www.hnp-mikrosysteme.de/download.

!

The "Declaration of media in contact with the micro annular gear pump and
components" must imperatively be filled in. The nature of liquid which entered
into contact with the micro annular gear pump and the components must be
specified.
In case of non-compliance, the sender will be liable for any resulting injure to
persons or any object damage.

«
...
57
58
59
60
61
...
»

Содержание mzr-2542




























































































Отзывы:

Нет отзывов

Похожие инструкции для mzr-2542

Бренд: Watson Marlow Pumps Страницы: 131

Бренд: Eaton Страницы: 57

Бренд: A.O. Smith Страницы: 2

Бренд: A.O. Smith Страницы: 2

Бренд: Navien Страницы: 108

Бренд: Gator Prime Страницы: 32

Бренд: EAS Electric Страницы: 165

Бренд: vacuubrand Страницы: 24

Бренд: Davey Страницы: 28

Бренд: ubbink Страницы: 29

Бренд: YANGTECH Страницы: 23

Бренд: Gardena Страницы: 16

Бренд: Zenit Страницы: 35

Бренд: F.F. Group Страницы: 28

Бренд: Comet Страницы: 12

Бренд: Zip Страницы: 24

Бренд: Bard Страницы: 38

Бренд: ArTi Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды