HNP Mikrosysteme mzr-2542 Скачать руководство пользователя страница 50

Страница: 50 / 91

6 Mounting/Installation

Operating manual mzr-2542 / mzr

2942

Technical data subject to change without prior notice!

Last update: January 2016

Startup of the micro annular gear pump with the S-BL control unit

speed regulation

serial interface of PC

external voltage supply
24 V DC / 2.5 A

Status LED

mzr-pump

switch S1

figure 30

Connection of the micro annular gear pump mzr-2542 or mzr-2942 and the S-BL control unit

Connect the motor cable to the 6-pole connector of the S-BL control unit.
The pin configuration is indicated in table 15.

Connect the RS-232 port of the MCBL3006 with a free serial interface of a
PC. For this purpose use the delivered 9-pole null-modem cable.

Put the potentiometer of the S-BL control unit to zero position by turning it
clockwise to the limit stop.

10.

Connect the voltage supply 24 VDC. This can be done with the integrated
DIN connector or, alternatively the 2-pole screw clamp (24 V = »+«;
GND = »-«). Pay attention to the correct polarity.

11.

You may now install the delivered software »Motion Manager« as
described in the chapter 9.

While connecting the DC voltage pay attention to the correct polarity,
otherwise electronics may be damaged.

Содержание mzr-2542




























































































Результаты поиска

Содержание mzr-2542

Отзывы:

Похожие инструкции для mzr-2542

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-2542, Руководство по эксплуатации

Результаты поиска

Содержание mzr-2542

Отзывы:

Похожие инструкции для mzr-2542

Бренды по названию

Популярные бренды