HNP Mikrosysteme mzr-2542 Скачать руководство пользователя страница 54

Страница: 54 / 91

7 The startup/shutdown of a pump

Operating manual mzr-2542 / mzr

2942

Technical data subject to change without prior notice!

Last update: January 2016

Nature of the handled liquid

Flushing cycle
[min]

Suitable flushing liquid

Oils, fats, plastifiers

15-20

isopropanol, ethanol, acetone, benzine

Solvents (polar + nonpolar)

5-10

isopropanol, ethanol

Other organic liquids

10-15

isopropanol , ethanol

Refrigerating and cooling agents 15-20

isopropanol,

ethanol

Neutral watery solutions 20-25

isopropanol,

ethanol

6 Basic

solutions

25-30

DI-water (deionized water)

7 Organic

acids

30-40

isopropanol, ethanol

Weak mineral acids

25-30

DI- water

Strong mineral acids 35-45

DI-

water

Strong oxidizing liquids

35-45

DI- water

Paints, varnishes, adhesives

50-60

Not specified - for further information
please contact HNP Mikrosysteme.

table 33

Selection of the flushing liquid (solvent) and the duration of the flushing cycle depending on the delivered
liquid.

Warning

Please make sure that the pump components and particularly O-rings and
sealing are resistant to the employed flushing liquid (see table 34).

Shaft sealing

O-ring material

Flushing liquid

PTFE (Teflon

graphite-

reinforced

UHMWPE

FKM

(Viton

)

EPDM

FFKM

acetone 0

benzene 0

benzyl alcohol

benzine 0

butanol 0

dimethyl sulfoxide (DMSO)

ethanol 0

isopropanol 0

methanol 0

methylethylketone (MEK)

oil / fine mechanics oil

styrene 0

toluene 0

water 0

xylene 0

Legend:

0 ... good suitability 1 ... suitability 2 ... conditional suitability 3 ... labile - ... not specified

table 34

Resistance of the sealing materials depending on the flushing liquid (solvent)

Содержание mzr-2542




























































































Результаты поиска

Содержание mzr-2542

Отзывы:

Похожие инструкции для mzr-2542

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-2542, Руководство по эксплуатации

Результаты поиска

Содержание mzr-2542

Отзывы:

Похожие инструкции для mzr-2542

Бренды по названию

Популярные бренды