HNP Mikrosysteme mzr-11507 Скачать руководство пользователя

Страница: 38 / 55

8 Startup/shutdown of a mzr-pump

Operating manual mzr-11507

Technical data subject to change without prior notice!

Last update: August 2016

Liquids

ilit

y in

ilit

th t

eliver

liq

ion of

age

reakaw

tor

que

xico

isco

sit

Descr

tio

isopropanol

solvent for organic compounds, cosmetics, essential oils
waxes, and esters, antifreezers, antiseptic agents

acetone

solvent for a number of organic compounds, unlimited
solubility in water, dissolves natural and synthetic resins, fats,
oils and commonly used plastifiers

ethanol

solvent for organic compounds, fats, oils and resins

DI-water

solvent for many organic and mineral liquids

fine mechanics
oil

cleansing and protective action (dissolves fats, tar, rubber or
adhesive substances, protects against corrosion).

hydraulic oil

lubricating and preserving properties (

Warning

: may resinate

or deteriorate with time)

nitrogen

is not a solvent, may leave deposits after drying out

air /
compressed air

is not a solvent, may leave deposits after drying out

Legend: + ... good/suitable o ... satisfactory; - ... bad/inadequate

table 11

Selection of the conservation agent

In order to prevent dust particles and foreign bodies from penetrating into the

pump or the conservation agent from leaking out, please secure the liquid

input and output openings with the delivered protective plugs or screws.

Warning

Water or DI-water should not be used as conservative liquids. They germinate

already after a few days and build a bio film which can later block the pump.

8.4.2

Dismantling of the system

−

Put the drive out of operation by turning down speed to 0 rpm and by

switching off the voltage supply. Make sure that the procedure described in

the chapter 8.3 has been completed.

−

Now that the pump has been stopped you may remove it from the system.

−

Protect the inlet and outlet openings of the pump with adapted protective

plugs or screws.

Содержание mzr-11507
























































Результаты поиска

Содержание mzr-11507

Отзывы:

Похожие инструкции для mzr-11507

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-11507, Руководство по эксплуатации

Результаты поиска

Содержание mzr-11507

Отзывы:

Похожие инструкции для mzr-11507

Бренды по названию

Популярные бренды