HNP Mikrosysteme mzr-11507 Скачать руководство пользователя

Страница: 11 / 55

2 Safety instructions

Operating manual mzr-11507

Last update: August 2016

Technical data subject to change without prior notice!.

2.3

Safety-conscious work

The safety instructions listed in this operating manual, the applicable national

regulations for accident prevents and all internal working, operating and safety

regulations of the operator must be complied with.

2.4

Safety instructions for the operator

The surface temperature of the motor under full load may exceed 60°C. If

needed, this surface should be protected on site against contact in order to

avoid skin burns.

The drive should be protected against dust, water vapor condensation,

humidity, splash water, aggressive gases and liquids. Please provide for

adequate air ventilation and thus cooling of the motor.

The micro annular gear pump mzr-11507 must not be used in areas exposed to

explosion risks or in the proximity of inflammable gases and vapors.

Possible leaks of dangerous liquids (for example from the shaft sealing) should

be guided away in a way not to represent any danger for the personnel and the

environment. The pump should be regularly checked for possible leakage. All

legal requirements in this matter should be followed.

The existing protections against contact for the moving parts of the pump (such

as for example the coupling) must not be removed during operation.

Take care that all risks resulting from the electric energy are excluded. (For

details please refer to the instructions provided by the authorities in charge or

your power supplier.)

Warning

Please insure, that the totality of the liquid supply accessories such as tubes,

hoses, filters etc. are free from dust or dirt particles. Impurities such as metal,

plastic or glass particles may impair or damage the pump leading to its failure.

Warning

Please, operate the pump with a filter featuring 10 µm or smaller pores. It will

protect the pump.

2.5

Safety instructions for maintenance, check and assembly of the pump

As a rule all maintenance work on the device should be performed when the

device is at a standstill. The shutdown

procedure described in this manual must

be followed. Pumps delivering liquids hazardous to health must be

decontaminated. Immediately after the work had been completed all safety

equipment and protection measures should be applied.

Before starting the operation, please take into notice the instructions listed in

the chapter 6.

Содержание mzr-11507
























































Результаты поиска

Содержание mzr-11507

Отзывы:

Похожие инструкции для mzr-11507

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-11507, Руководство по эксплуатации

Результаты поиска

Содержание mzr-11507

Отзывы:

Похожие инструкции для mzr-11507

Бренды по названию

Популярные бренды