HNP Mikrosysteme mzr-11507 Скачать руководство пользователя

Страница: 32 / 55

8 Startup/shutdown of a mzr-pump

Operating manual mzr-11507

Technical data subject to change without prior notice!

Last update: August 2016

Startup/shutdown of a mzr-pump

8.1

Prepare for start up

After the liquid supply system had been completed, please check once again

the operating conditions of the micro annular gear pump as according to the

following points:

−

Are the inlet and outlet tubes correctly connected?

−

Is the entire liquid supply system clean - that means free of particles, foreign

bodies, pollution or swarf?

−

Has a filter been installed on the suction side?

−

Has a sufficient amount of the right liquid been supplied?

−

The pump does not run the risk of a longer dry operation?

−

The entire liquid supply system has been checked for leakage?

−

Is it possible to stop the pump by an emergency switch if an unexpected

malfunction occurs at the startup?

8.2

Startup of the micro annular gear pump

Switch on the voltage supply. The micro annular gear pump can now be put

into operation by turning on the potentiometer knob or by sending a nominal

external voltage signal.

Start the filling in of the pump at low or middle speed (1000 - 3000 rpm).

Warning

Avoid dry operation of the pump over a longer time. The pump should be

filled in before it is put to operation.

8.3

Flushing procedure after use

After each service the micro annular gear pump should be carefully flushed

with a non-corrosive, filtered and particle-free flushing liquid (see table 9 and

table 10). During flushing procedure the pump should operate at a speed of

about 3000 rpm

and if possible against a low pressure (that can be obtained by

using a restrictor, a capillary or similar). The flushing liquid must be compatible

with the delivered liquid and suitable for solving the remaining liquid rests.

Depending on the application for example water, or isopropanol may be used.

If you have doubts whether a particular liquid is suitable for this function or

not, please ask the manufacturer of the liquid or HNP Mikrosysteme.

Содержание mzr-11507
























































Результаты поиска

Содержание mzr-11507

Отзывы:

Похожие инструкции для mzr-11507

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-11507, Руководство по эксплуатации

Результаты поиска

Содержание mzr-11507

Отзывы:

Похожие инструкции для mzr-11507

Бренды по названию

Популярные бренды