HNP Mikrosysteme mzr-11507 Скачать руководство пользователя

Страница: 23 / 55

5 Optional modules

Operating manual mzr-11507

Last update: August 2016

Technical data subject to change without prior notice!.

5.3

Heating module

5.3.1

Electric heating module

The electric heating module enables active heating of the pump head up to

120° C (248 °F) operating temperature. The heating module consists of a

heating jacket covering the pump head and a thermal element type L.

Depending on the pump size, the thermal element will be integrated on the

pump head in different ways. In order to adjust the temperature of the pump

head, an additional heat regulating device may be delivered.

Connection cable for

electric band heater

Thermoelectric couple

Electric heading

jacket

figure 11

Micro annular gear pump with the electric heating module (figure with mzr-2905)

Before connecting the heating jacket and the thermal element to the power

supply, please observe the following technical data.

Thermal element

Type

MT-1.5

Thermal element

Type J (Fe-CuNi IEC 584)
alternativ:
Type L (Fe-CuNi DIN 43710)

Temperature measuring range

0 to 400 °C

Diameter of the sensing device

1.5 mm

Material

V4A (1.4541)

Cable length

0,8 m

Heating jacket

mzr-11507

Voltage

230 VAC

Power output

600 W

Diameter

70 mm

Width

approx. 50 mm

Cable length

0,8 m

table 5

Technical data of the electric heating module

Содержание mzr-11507
























































Результаты поиска

Содержание mzr-11507

Отзывы:

Похожие инструкции для mzr-11507

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-11507, Руководство по эксплуатации

Результаты поиска

Содержание mzr-11507

Отзывы:

Похожие инструкции для mzr-11507

Бренды по названию

Популярные бренды